469918

Carrera Digital 124 - 30352 Control Unit Manual

6
Zoom out
Zoom in
Previous page
1/6
Next page
11
Sound ON/OFF








The conrmation sound when crossing the sensors and the key
sound can be switched o. Switch o the Control Unit and keep the
“START/ENTER” button
pushed, switch on the racetrack and
release “START/ENTER”
again. The acknowledgement sound
for switching on the Control Unit cannot be switched o however.
Reset function








To restore the Control Unit to factory settings the Control Unit oers
a reset function.
Switch o the Control Unit and keep the “ESC/PACE CAR”
but-
ton pushed; switch on the ractrack and release the button again. All
previous settings for speed, braking performance, tank fuel capac-
ity, sound and lap counting will be restored to factory settings. The
cars´ settings will remain unaected by this measure unless they are
placed on the racetrack.
Factory settings:
• speed = 10
• braking performance = 10
• tank capacity = 7
• sound = ON
• display of position for Autonomous and Pace Car = OFF
Energy-saving mode
After 20 minutes of non-usage the Control Unit switches to energy-
saving mode and all displays such as Position Tower, Driver Dis-
plays and Startlight are turned o. To reactivate shortly press any
speed controller´s tappet or push lane-change button at the speed
controller or control key at the Control Unit. All settings will be kept.
Starting sequence



Driving without starting sequence:
1. Switch on the Control Unit (ON-OFF)
2. After approx 1 second the central LED lights permanently and a
brief acoustic signal will sound , g
3. Place the car/s on the connecting track
4. In this mode the track is cleared without starting light signal; you
can start immediately.



With the starting sequence being initiated all displays will be reset.
1. Switch on the Control Unit (ON-OFF)
2. After approx 1 second the central LED lights permanently and a
brief acoustic signal will sound , g.
.
3. Then push start button until all LEDs will light, g.
.
4. Place the car/s on the connecting track, g.
.
5. Push start button again - the starting sequence is initiated, the
LEDs are lit and acoustic signals can be heard.
6. With elapse of the starting light procedure (LEDs light individu-
ally) the race is released, g.
.
7. False start: If a car´s speed controller is actuated during the
starting light phase, this is rated as false start. The vehicle having
caused the false start will travel a short distance and the LED on
the relevant car or speed controller will ash. The race will not be
released and the start has to be repeated.
Maintenance and care
To ensure a proper operation of the motor-racing circuit, all race-
track components should be regularly cleaned. Pull the plug prior
to cleaning.
 Keep the track surface and track slots clean with a
dry cloth. Do not use any solvents or chemicals for cleaning. When
it is not in use, store the racetrack in a clean and dust-protected
location, preferably in the original cardboard box.
Troubleshooting
Driving tips

In case of any malfunctions, please check the following:
• Has the connection to the power supply been established correctly?
• Have transformer and speed controllers been connected
correctly?
• Are the track connections faultless?
• Are the racetrack and track slots clean and free of any foreign
objects?
• Are the sliding contacts in order and do they make contact with
the track slot?
• Are the cars correctly coded to the according speed controller?
• The track‘s current feed will be switched o automatically for 5
seconds, if there is an electrical short circuit: this will be notied by
audible and visual signals.
• Are the cars placed on the track in running direction? In case of
non-functioning push the running direction switch which is on the
car´s bottom.

During operation small car parts as spoilers or mirrors may get o or
brake due to being original detailed parts of the car model. To avoid
this it is possible to remove them before operation.

• You can drive fast along the straight track but you should brake
before the curve and then accelerate again when coming out of the
curve.
• Do not fasten or block the vehicles when the motor is running:
overheating or damage to the motor could result otherwise.
 When using track systems which are not manufactured by
Carrera the existing guide keel has to be replaced by the special
guide keel (#85309). While using the Carrera crossing (#20587) or
high banked curve 1/30° (#20574) slight driving noise might occur
which is due to the full-scale genuineness and does not aect aw-
less operation.
All Carrera spare parts are available in the webshop:

Delivery exclusively to Germany, Austria, Netherlands, Belgium and
Luxembourg.
Technical specifications

18 V
54 VA (Carrera DIGITAL 124)
14,8 V 51,8 VA (Carrera DIGITAL 132)

1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED ashes at
long intervals.
By operating the speed controller the stand-by mode is nished,
the racetrack returns to idle-mode again.
4.) O-state = power supply unit disconnected from mains supply
This device is marked by “selective sort throught” symbol related to
sort through domestic, electric and electronic, waste. This means
the product must be treated by a specialized “sorting/collecting” sys-
tem in accordance with European directive 2002/96/CE, to reduce
the impact upon environment. For more precise information, please
contact your local administration. Electronical product which are not
going through special collecting, are potentially dangerous for envi-
ronment and human health, because of dangerous substance.

18 V
54 VA (Carrera DIGITAL 124)
14,8 V 51,8 VA (Carrera DIGITAL 132)

1.) Operating mode = cars are operated via speed controllers
2.) Idle mode = speed controllers not activated, no game
3.) Stand-by mode = after approx. 20 minutes idle mode the
connecting section switches to stand-by mode. LED ashes at
long intervals.
By operating the speed controller the stand-by mode is nished,
the racetrack returns to idle-mode again.
4.) O-state = power supply unit disconnected from mains supply
6


Need help? Post your question in this forum.

Forumrules
1

Forum

carrera-digital-124---30352-control-unit

Reset search

  • can i get a copy of the carrera eb control display panel Submitted on 22-5-2022 at 20:52

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera Digital 124 - 30352 Control Unit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera Digital 124 - 30352 Control Unit in the language / languages: English as an attachment in your email.

The manual is 2,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info