469906

Carrera Digital 124 - 23607 TITANS OF RACING Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
12
Unscrew the rear axle, take o the axle carrier (a) (g.
) and turn
it by 180° (g.
). Put the axle carrier on to the rear axle and screw
it tight at the engine block (g.
). Insert the engine block in the
chassis and screw it tight. Fit the cables together according to their
colours.
Changing the light board
 Depending on the model, the light boards might be
screwed tight.
To change the light boards unscrew the car’s upper
part from the chassis. Unscrew the front axle according to g.
and remove the cables between the front light and the car board (g.
). Slightly bend down the catch hook (g.
) and pull up the light
board. Insert the light board (g.
), until the catch hook latches
in. Screw in the front axle and t the cables together according to
their colours.
Remove the cables between the rear light and the car
board according to g.
Slightly bend down the catch hook (g.
) and pull up the light board. Insert the light board until the catch
hook latches in (g.
) and t the cables together according to
their colours.
Race modes

1. Switch on the Black Box (ON-OFF)
2. After approx. 1 second the central LED will illuminate perma-
nently and a brief acoustic signal will sound.
3. Position the car/s on the connecting track
4. In training mode, the track is released without signal from the
trac light; you can start immediately

1. Switch on the Black Box (ON-OFF)
2. After approx. 1 second the central LED will illuminate perma-
nently and a brief acoustic signal will sound.
3. Afterwards, press the start button until all LEDs light up
4. Position the car/s on the connecting track
5. Press the start button again – the starting sequence will be initi-
ated, the LEDs will illuminate and acoustic signals will sound.
6. Once the trac light phase has expired (LEDs light up individu-
ally), the race is released
7. False start: If a car’s speed controller is actuated during the trac
light phase, this is rated as false start. The vehicle that has caused
the false start will travel a short distance and the LED on the rel-
evant vehicle or hand control will ash. The race is not released and
the start has to be repeated.
Light function on/off
3 sec.
STOP
The car programmed to the speed controller will have to come to a
stop for at least 3 seconds before the light can be switched on or o
by the push of the lane-change-button.
Coding/decoding
of the cars to the according
speed controller
2x CLICK
2x CLICK
Place car on the track, push lane-change-button twice g.
, lift car
at the front, put car back again g.
, while car´s lights are ashing
push lane-change-button twice g.
. Programming is conrmed
by a tone. All settings are saved until new programming is carried
out.
Autonomous Car function
300
15 0
250
200
0
100
50
4x CLICK
Place car on the track, push lane-change-button twice, lift car at the
front, put car back again (see coding/decoding g. 1 + 2). While
car´s lights are ashing push lane-change-button 4 times g.
.
Start car, push lane-change-button for requested speed g.
(ir-
respective of the car´s position). Autonomous car will drive at this
speed automatically and consistently until its decoding.
Decoding is eected by holding the car. For new coding see coding/
decoding.
Pace Car function
Pit Stop 30346
300
15 0
250
200
0
100
50
6x CLICK
Place car on the track, push lane-change-button twice, lift car at the
front, put car back again (see coding/decoding g. 1 + 2).
While car´s lights are ashing push lane-change-button 6 times g.
. Start car, push lane-change-button for requested speed g.
(irrespective of the car´s position). Car will assume this speed con-
sistently and will enter the next Pit Stop automatically g.
.

Start Pace Car by pushing the button at the Black Box g.
. After
10 seconds each lane switch will change independently until the
Pace Car enters the Pit Stop. Carry out car decoding (see point
coding/decoding).
Setting basic speed
1

1 – 10
1 – 10
(individually for one and/or several cars)
Plug any speed controller in connector 1. Switch o Black Box,
place car/s on the track, push lane-change-button and keep it
pushed while Black Box is switched on again. Don´t release the
lane-change-button until the 1st LED lights red. Levels are set by
pushing lane-change-button. Conrm speed by pressing the speed
controller´s tappet (thumb) (=> middle LED will light).
1 LED on = low speed
5 LEDs on = high speed
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera Digital 124 - 23607 TITANS OF RACING at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera Digital 124 - 23607 TITANS OF RACING in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info