616842

Carrera 521 Manual

17
Zoom out
Zoom in
Previous page
1/43
Next page
34 35GBGB
08. REPLACEMENT PARTS
Cutting elements are subject to natural wear and excluded from the
warranty. In order to achieve optimum shaving results, it is indispensa-
ble to replace these parts in time.
You can order the following replacement parts:
Shaving foil / cutting blades
4-track shaving system (4-track shaving system with integrated long
hair trimmer and 3 spring-loaded cutting blades).
Recommended replacement intervals
To guarantee optimum cutting performance, we recommend replacing
the shaving foils and cutting blades at the latest every 12 months.
Since both cutting parts adapt to each other over time, we recommend
replacing the shaving foil and cutting blade at the same time.
The replacement parts can be ordered online or via the Service Centre.
Replacing the parts
WARNING! Risk of cutting injuries!
Carefully pull the three cutting blades off the white plastic
holder.
1. Remove the protective cap.
2. Press the unlocking buttons
4
on both sides and remove the shav-
ing head.
3. Tilt the old cutting blades out of their holder (see fig. J).
4. Grasp the new cutting blades on both ends between your thumb
and index finger and insert them into the white holder. Briefly press
the cutting blades down until they lock into place with an audible
click.
5. Remove the old shaving foil frame from the shaving head frame.
With a fingernail, grasp behind one of the two flaps (see fig. K) on
the shaving foil frame and tilt it out.
6. Carefully press the new shaving foil frame into the shaving head
frame until it locks in place with an audible click.
Cleaning after dry shaving
1. Press the lateral unlocking buttons
4
and remove the shaving
head
2
.
2. Knock the shaving head on a flat surface and/or blow it out.
3. Clean the cutting blades with the cleaning brush.
CAUTION!
Do not use force and do not press onto the shaving foil!
Wet cleaning
1. Before cleaning, unplug the 5V plug
12
from the shaver (see fig. A
and B).
2. Use the on/off switch
6
to switch off the shaver.
3. Press both unlocking buttons
4
to release the shaving head
2
(see fig. E).
4. Pull off the shaving head
2
in an upward direction (see fig. A).
5. Carefully clean the inside and outside of the shaving head under
warm, running water (see fig. G).
6. Hold the shaver above the sink.
7. Carefully rinse the upper part of the shaver and the cutting
blades under warm, running water (see fig. H).
8. Use the on/off switch
6
to switch on the shaver without the shav-
ing head attached. Let it run for approx. 5–10 seconds to shake the
water drops off the cutting blades
3
.
9. Allow the parts to dry well.
10. Firmly attach the shaving head to the shaver until it locks into place
with an audible click (see fig. F).
11. Replace the protective cap
1
on the shaver.
The shaver is again ready for operation.
NOTE: Apply 1–2 drops of acid-free oil (e.g. sewing machine oil) onto
the cutting blades and the long hair trimmer, especially after wet
cleaning and the replacement of spare parts. Let the appliance run for
a couple of seconds without using it. Use a soft cloth to wipe off the
excess oil, if necessary.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera 521 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera 521 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 8,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info