550886
11
Zoom out
Zoom in
Previous page
1/84
Next page
21
GREEN = ReadyRED = Charging
1
1
2
ON
1
11
The Carrera RC helicopter and the
remote control are frequency bound at
purchase. Should there occur any prob-
lems with the communication between
the Carrera RC helicopter and the
remote control at the beginning, please
carry out a new frequency bind.
Press the right joystick on the remote control from above and switch on the remote control.
Insert the battery into the helicopter.
• The control LED starts to flash slowly and an acoustic signal is sounded.
Push the left-hand joystick on the controller up to the stop at the top and down to the
stop at the bottom twice.
• The control LED lights up permanently again and indicates that the frequency bind
has been finished.
Frequency bind between model
and remote control
Checklist for flight preparation
Preparing the first flight
Note: Push the battery right to the stop in the battery compartment, that is, until the
front end of the battery makes contact with the front of the mounting. This will guaran-
tee that the centre of gravity is ideally located and that the flying performance is at its
optimum. To switch on the helicopter, connect the plugs for the battery and the heli-
copter. To switch off, disconnect the plugged connection.
Inserting the LiPo rechargeable battery
in the helicopter
Inserting the batteries
in the remote control
Please make sure that you charge the provided
7.4 V
1000 mAh
LiPo rechargeable
battery only with the provided
8.4 V
1000 mA
LiPo battery charger. Rechargeable
batteries are to be removed from the toy before being charged. In case you try to
charge the rechargeable battery with a dierent LiPo battery charger or any other bat-
tery charger, this might cause serious damages. Please carefully read the previous
chapter about warnings and guidelines on the usage of rechargeable batteries before
proceeding. Supply terminals are not to be short-circuited.
Please proceed as follows when charging the rechargeable battery with the appropri-
ate battery charger:
Connect the battery charger to the power socket. The green LED on the power
supply unit indicates that the charger has correctly been connected to the power
socket or that the rechargeable battery has been fully recharged.
Connect the rechargeable battery to the charger. The connecting section or the con-
nection between battery and charger are specially designed to avoid reverse polarity.
Has the discharged battery been inserted correctly, the red LED on the charger will
light up to indicate that the battery is now being recharged.
It takes approximately 1 hour to recharge a discharged battery (not exhaustively
discharged). As soon as the battery is completely charged the LED on the charger
lights up green.
Note: When delivered, the LiPo rechargeable battery is partly charged. Therefore the
first charging might take slightly shorter.
Open the battery compartment with a
screwdriver and insert the batteries in
the remote control. Please keep in mind
the correct polarity. Different types of
batteries or new and used batteries are
not to be mixed. After having closed the
compartment you can check all func-
tions of the remote control with the help
of the power-switch on the front. With
the power-switch turned ON and proper
functioning, the top center LED on the
remote control will light up red.
When the control LED flashes rapidly,
the batteries in the controller must be
changed.
After the LiPo battery has been fully
charged it can be inserted in the heli-
copter. Therefore push the battery from
behind into the battery holder at the
bottom side of the helicoptes body.
Please make sure that the plug faces
towards the front of the helicopter.
This checklist does not replace the contents of the operating instructions. Although it
can be used as a quick-start-guide we strongly advise to first read the operating
instructions in detail before you proceed.
Check the contents of the package
Connect the charger to the power socket
Charge the LiPo battery
Insert four AA batteries in the controller
Insert the fully charged LiPo battery in the helicopter
Look for a suitable environment for flying
Place the helicopter on a flat surface
Always switch on the remote control first and then the helicopter
Check the control system
Make yourself familiar with the control system
This checklist does not replace the contents of the operating instructions. Although it
can be used as a quick-start-guide we strongly advise to first read the operating
instructions in detail before you proceed.
• Generally switch on the remote control first.
• Insert the battery in the designated holder at the helicoptes bottom.
• Place the charged helicopter on a flat surface and wait a moment until the system is
correctly initialised and is ready for use.
• The LED in the helicopter now flashes in rhythmically-accelerating sequence.
• Push the left-hand joystick slowly and with care up to the top and down to the
bottom twice to activate the existing connection.
• The LED in the helicopter is now lit continuously.
• The helicopter is now ready to be flown.
• If the helicopter fails to display any function, connect the model with the controller as
necessary, as shown below.
• Fly the model
• Land the model
• Take the LiPo battery out of the helicopter
• Always switch off the remote control last
• Always keep the rechargeable battery stored outside the helicopter
Recharging the LiPo rechargeable battery
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carrera 501001 Sky Hunter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carrera 501001 Sky Hunter in the language / languages: All languages as an attachment in your email.

The manual is 9,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Carrera 501001 Sky Hunter

Carrera 501001 Sky Hunter Additional guide - English - 2 pages

Carrera 501001 Sky Hunter Additional guide - German - 1 pages

Carrera 501001 Sky Hunter Additional guide - German, French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info