792903
99
Zoom out
Zoom in
Previous page
1/116
Next page
98
Toujours faire une couture d'essai sans
ce pied et ne l'utiliser qu'en cas de
besoin.
Ce pied de transport supérieur égalise
l'avancement du tissu supérieur et inférieur
et améliore le rapport de plaids, rayures et
motifs. Ce pied favorise l'avancement
régulier sur des tissus difficiles.
1.Relever la barre du pied.
2.Retirer le support du pied en dévissant
la vis (3).
3.Fixer le pied de transport supérieur
comme illustré:
i) La vis de fixation doit se trouver entre
les branches. (2)
ii) Glisser de gauche à droite la tête de
fixation en plastique qui doit
parfaitement se placer sur la barre du
pied.
iii) Abaisser la barre du pied.
iv) Visser la vis de fixation.
4.Veiller à ce que la vis de fixation et celle
du pied soient parfaitement vissées.
5.Ramener le fil de canette sur l'endroit et
diriger les deux fils vers l'arrière sous le
pied.
a Branche
b. Bouton de fixation
c Plaque à aiguille
d Vis de fixation et support d'aiguille
e Vis de fixation du pied
f Barre du pied
.
.
.
.
.
Vždy zkuste nejprve šít bez patky
vrchního podávání a použijte ji jen
tehdy, pokud je to nutné.
Patka vrchního podávání, která je k
dostání, vyrovnává podávání vrchní a
spodní látky a zlepšuje lícování plédu,
pás a vzor . Tato patka zamezuje
nerovnom rnému podávání u velmi
problematických látek.
1.Nazdvihn te patkovou ty .
2.Vyjm te držák patky tak, že povolíte
šroub (3).
3. Na stroj nasa te patku vrchního podávání
následovn :
i) Upínací šroub jehly se musí nacházet
ve vidlici. (2)
ii) Plastovou upínací hlavu posu te zleva
doprava tak, aby byla na patkové ty i.
iii) Spus te patkovou ty .
iv) Utáhn te upínací šroub.
4. Dávejte pozor na to, aby byl upínacíšroub
jehly a upínací šroub patky pevn dotažen.
5.Vytáhn te spodní nit a ob nit položte
dozadu pod patku vrchního podávání.
a Vidlice
b Upínací hlava
c Jehelní ty
d Upínací šroub jehly & držák
e Upínací šroub patky
f Patková ty
ůů
ě
ě
ě
ď
ě
ň
ť
ě
ě
ěěě
č
č
č
č
č
.
.
.
.
.
.
Patka vrchního podávání
Pied de transport supérieur
Walking foot
FR
CZ
EN
Always try to sew first without the
walking foot accessory which should
be used only when necessary.
The "Walking foot" accessory equalizes
the feeding of the upper and lower layers
of fabric and improves the matching of
plaids, stripes and patterns. This foot
helps to prevent uneven feeding of very
difficult fabrics.
1.Lift the presser foot bar.
2.Remove the "presser foot holder".
3.Attach the "walking foot" to the machine
in the following way.
i) The fork arm should fit into the
needle screw and clamp. (2)
ii) Slide the plastic "attaching head"
from your left to right so that it is
fitted on the "presser foot bar".
iii) Lower the "presser foot bar".
iv) Tighten the fixation screw
4.Make sure both the "needle screw" and
the "fixation screw" are tight.
5.Draw the bobbin thread up. Lay both
threads t the back under the foot.
a. Fork arm
b. Attaching head
c. Needle bar
d. Needle screw & clamp
e. Presser bar attaching screw
f. Presser foot bar
o
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carina Power and Stretch II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carina Power and Stretch II in the language / languages: English, German, French as an attachment in your email.

The manual is 1.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info