792903
47
Zoom out
Zoom in
Previous page
1/116
Next page
46
This is a simple operation but it is important to
carry out correctly as by not doing so several
sewing problems could result.
. Start by raising the needle to its highest
point, and continue turning the handwheel
counterclockwise until the needle just slightly
begins to descend. Raise the presser foot to
release the tension discs.
For safety, it is strongly suggested you
turn off the power before threading.
. Lift up the spool pin. Place the spool of thread
on the holder with the thread coming off the
spool as shown. For small thread spools, place
small side of spool holder next to spool.
. Draw thread from spool through the upper
thread guide.
. Pulling thread through pre-tension spring as
illustrated.
. Thread tension module by leading thread
down right channel and up left channel.
During this process it is helpful to hold the
thread between the spool and thread guide.
. At the top of this movement pass thread from
right to left through the slotted eye of the
take-up lever and then downwards again.
. Now pass thread behind the thin wire needle
clamp guide and then down to the needle
which should be threaded from front to back.
8. Pull about 6-8 inches of thread to the rear
beyond the needle eye. Trim thread to length
with built-in thread cutter.
If your sewing machine is equipped with the
factory installed optional automatic needle
threader, instructions for use can be found on
page .
1
2
3
4
5
6
7
47
Note:
Note:
Cette opération est simple. Néanmoins, il est
important de l'exécuter correctement sous
peine de faire éventuellement face à plusieurs
problèmes de couture.
.
le pied
presseur pour libérer les disques de tension .
Pour des raisons de sécurité, il est
fortement recommandé de couper
l'alimentation électrique avant l'enfilage.
2.
sur le porte-bobine, le fil sortant
de la bobine tel qu'illustré.
. Passez le fil de la bobine à travers le guide-fil
supérieur.
Enfilez maintenant l'oeillet du releveur de fil
7
8. Enfilez ensuite le chas de l'aiguille de l'avant
vers l'arrière et tirez à peu près 15 cm de fil
vers l'arrière de la machine. Coupez le fil à la
longueur désirée à l'aide du coupe-fil
incorporé.
Si votre machine à coudre est équipée d'un
enfileur automatique déjà installé en sortie
d'usine, tournez à page pour
instructions d'usage.
1
47
Tournez le volant pour lever l'aiguille dans sa
position la plus haute et relevez
Levez le porte-bobine horizontal. Placez une
bobine de fil
3
4. Guider le fil autour du guide en le tirant à
travers le ressort de pré tension tel qu'illustré.
5. Enfilez le module de tension en guidant le fil
vers le bas via la rainure droite et vers le
haut via la rainure gauche. Au cours de cette
opération, il est utile de tenir le fil entre la
bobine et le guide-fil et de le tirer doucement
vers le haut.
6.
en y passant le fil de droite à gauche et
guidez le fil à nouveau vers le bas.
. Passez le fil dans le guide-fil horizontal qui se
trouve sur le pince-aiguille.
la des
Note:
Note:
Navléknutí vrchní nit
1. Umístěte jehlu do vysoké polohy a poté
nadzvedněte šicí patku, čímž uvolníte
vypínací kotouče.
Z bezpečnostních důvodů
důrazně doporučujeme stroj před
navlékáním vypnout.
2. Nadzvedněte držák špulky. Nasuňte špulku
na držák tak, aby nit směřovala ze špulky
jako na obrázku. U malých špulek by se měla
úzká strana stojánku na špulku umístit vedle
špulky.
3. Protáhněte nit ze špulky podle obrázku skrz
vedení vrchní nitě.
4. Potom skrz pružinu napínače.
5. Provlékněte nit skrz modul napínače,
přičemž nit nejprve povedete v pravém
otvoru směrem dolů a potom v levém otvoru
zase směrem nahoru.
6. Protáhněte nit úplně nahoře zprava doleva
skrz očko niťové páčky a následně zase
dolů.
7. Provlékněte nit skrz vodicí sponu z tenkého
drátu a poté směrem dolů k jehle, kterou
provlékněte zpředu dozadu.
8. Sestřihněte nit integrovaným nožem na
správnou délku.
Pokud je váš stroj vybaven automatickým
navlékačem nitě, použijte jej tak, jak je popsáno
na straně 47.
ě je snadné, musí se však
provést bezpodmínečně správně. V opačném
případě se mohou při šití objevit různé
problémy.
Upozornění:
Pozor:
Navléknutí vrchní nitě
Enfilage du fil supérieur
Threading the upper thread
FR
CZ
EN
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carina Power and Stretch II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carina Power and Stretch II in the language / languages: English, German, French as an attachment in your email.

The manual is 1.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info