497568
5
Zoom out
Zoom in
Previous page
1/12
Next page
English
3. Search for Bluetooth devices on your phone by following the
phone’s instructions. Please consult your phone’s User Manual
for more information.
4. After a few seconds the phone will list the scala-rider
TeamSet as a discovered device. Select it and follow your
phone’s instructions to accept the pairing.
5. When prompted enter 0000 (four zeros) as your PIN or passkey.
6. Your phone will conrm that pairing has succeeded and the
headset will begin ashing slowly in Blue.
NOTE: If the Pairing process is not completed within two minutes the
headset will return to Standby mode.
With some mobile phones, you may need to tap the CTRL button
to connect the headset to the phone after pairing is complete. The
scala rider TeamSet headset will automatically connect to the last
phone connected to the headset.
SET UP FOR BLUETOOTH GPS DEVICE
If you have a Bluetooth enabled GPS device and would
like to transmit navigation instructions and sounds
from the GPS device through the headset’s speakers,
please follow instructions described in section below
TO PAIR THE scala rider TeamSet TO A Bluetooth GPS DEVICE”
If you want to use your mobile phone and your GPS device with the
scala rider TeamSet Driver’s unit headset, you should proceed as
follows:
1. Pair your GPS device to your mobile phone (Please consult your GPS
devices User Manual for more information).
2. Pair your headset to the GPS device as described below.
NOTE: Not all Bluetooth enabled GPS devices allow connections to
Bluetooth headsets like the scala rider TeamSet. Please consult your
GPS devices User Manual for more information.
TO PAIR THE SCALA RIDER TEAMSET TO A BLUETOOTH GPS
DEVICE:
1. Turn on your GPS device.
2. With the Driver’s unit headset turned OFF, press and hold
the CTRL Button until the Red and Blue Lights begin rapidly
alternating.
3. Search for Bluetooth headsets on your GPS device by following
the device’s instructions. Please consult your GPS device’s User
Manual for more information.
4. If your GPS device prompts for a PIN or Passkey enter 0000
(four zeros).
5. Your GPS device will conrm that pairing has succeeded. The
headset will begin ashing slowly in Blue.
6. If you wish to use a Bluetooth mobile phone to make and
receive calls through the headset, you must now pair your
mobile phone to your GPS device by following your GPS and/
or mobile phone’s instructions.
NOTE: If the Pairing process is not completed within two
minutes the headset will return to Standby mode.
PAIRING BETWEEN THE PASSENGER
AND DRIVER HEADSETS
The two headset units (Driver and Passenger units) are supplied facto-
ry paired. Therefore, you do not need to pair these devices. However,
if re-pairing is needed you may proceed as follows:
1. Make sure that both units are turned ON and close to each other.
2. Press the Intercom Buttons of both devices simultaneously for at least
10 seconds, the red Status Light of the passenger unit will light steadily.
3. If successful, the blue Status Light of the passenger unit will ash.
4. If pairing has failed, the red Status Light of the passenger unit will
turn o and you must repeat the procedure.
5
scala rider
®
TeamSet
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cardo scala-rider TeamSet at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cardo scala-rider TeamSet in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cardo scala-rider TeamSet

Cardo scala-rider TeamSet User Manual - German - 12 pages

Cardo scala-rider TeamSet User Manual - Dutch - 12 pages

Cardo scala-rider TeamSet Quick start guide - Dutch - 20 pages

Cardo scala-rider TeamSet User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info