232599
6
Zoom out
Zoom in
Previous page
1/12
Next page
6
scala rider
®
FM
2. Slide the Back Plate between the internal padding
and the external shell of the helmet.
3. Adjust the clamp’s location so that the
microphone is located opposite your
mouth and then tighten the screws.
You may need to reposition the Clamp
repeatedly until you identify the best
spot. The microphone must be positioned
vertically and not horizontally.
Glue Plate Method
You have the option to glue the Helmet Clamp
onto your helmet, when the above standard method cannot be
used, or in case you prefer to secure the Helmet Clamp with adhesive
glue. This option has been successfully used for a range of high end
helmets.
NOTE: While we have no reason to believe that the gluing
option might negatively affect any helmet, Cardo
does not assume any responsibility to that affect, ir-
respective of its nature and circumstances. The Glue
Plate is offered as a free option that you may choose
to use at your own risk and subject to renouncement
of any future claims.
Caution: This process can be done only once!
1. Use the enclosed Allen Wrench to remove both Allen screws
and release the Helmet Clamp’s back plate.
2. Determine the location on the helmet where the
Helmet Clamp must be attached.
3. Adjust the Helmet Clamp’s location on the Helmet so that the
microphone is located opposite your mouth. You may need to
reposition the Clamp repeatedly until you
identify the best spot. The microphone must
be positioned vertically and not horizontally
(Be sure to clean the selected area prior to
the gluing process as described in # 4 below).
4. Use the pre-moistened Towelette to clean the helmet
area where you want to install the Glue Plate. Allow to dry
thoroughly.
5. Peel the foil cover from the Glue Plates’ adhesive pad.
6. Place the Glue Plate into position according to #3. Press rmly 15
seconds on all 3 parts of the Glue Plate.
7. The adhesive pad bonds to full strength over the next 24 hours.
Therefore it is recommended to not use the headset during this 24
hour period.
8. Fasten the Clamp to the Glue Plate using the Allen screws that were
previously removed.
POSITIONING THE SPEAKERS
Attach the speakers to the Velcro inside your helmet opposite your ears
(short speaker cord for the left ear [A] and the long speaker cord [B] for
the right ear). You may want to use the sup-
plied Velcro pad.
Using two speakers inside the
helmet may be prohibited in
certain jurisdictions. If this is the
Speaker A
Speaker B
6
scala rider
®
FM
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cardo scala rider fm at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cardo scala rider fm in the language / languages: English as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cardo scala rider fm

Cardo scala rider fm User Manual - German - 12 pages

Cardo scala rider fm User Manual - Dutch - 11 pages

Cardo scala rider fm User Manual - French - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info