816467
44
Zoom out
Zoom in
Previous page
1/52
Next page
8786
Interval Maintenance work Personnel
yearly Safety inspections of
- electric systems
- motor
Qualified electricians
in case of an error Visual check
- of the entire machine
- of the cutter head and cutting table
Operating personnel
Visual check
- water pump
Specialist personnel
re-tightening and adjusting cutter head and cutting table Operating personnel
in case of damage change and replacement
- entire machine
- tool holder (flange and blade holder)
- tools (cutting blade)
- control elements (handles, locking rollers, etc.)
- water tank and hoses
- cutter head and cutting table
Operating personnel
change and replacement
- electric systems
- motor
- Water pump
Qualified electricians
STEPS AFTER COMPLETING MAINTENANCE
Aer completion of the maintenance works and before switching on, follow the following steps:
1. Check for tightness all threaded joints previously detached.
2. Check the proper installation of all previously removed protective devices and covers.
3. Make sure that all tools, materials and other equipment have been removed from the working zone.
4. Clean the working zone and remove any spilled substances such as liquids, processing materials or similar.
5. Make sure that all safety devices of the system function properly.
Error message / error Possible cause Troubleshooting Personnel
When switched on, the
machine does not start
Mains plug is loose Check proper connection to
mains
Operating personnel
Mains plug is defective Check the mains plug
for operability, replace if
necessary
Qualified electricians
Loose connection in the
electric system
Have the entire electric
system of the machine
checked
The drive motor is
defective
Have the drive motor
checked, replace if necessary
The main switch is
defective
Have the main switch
checked, replace if
necessary.
The machine does
not provide suicient
performance
The mains plug is too
long, cord reel is wound
up
Observe the prescribed
length of the mains plug .
Unwind the cable cord
Operating personnel
Capacity of the local mains
is insuicient
Pay attention to and observe
the ma chine connection data
The drive motor does
not maintain the rotation
speed
Have the drive motor
checked, replace if necessary
Qualified electricians
Low or no cooling water
feed
The water pump sucks air Fill the tank with water;
swivel the pump with the
suction side downwards
Operating personnel
Hose are clogged Clean the hoses
Hoses bent Check hose layout
A hose is leaky or
detached
Replace or re-attach the hose
properly
The water pump wheel or
strainer is polluted
Clean the pump wheel or
strainer
Water pump does not
function
Have the electric supply line
checked, replace if necessary
Qualified electricians
Motor does not start Mains plug is not properly
plugged.
Check the mains plug for
proper connection
Operating personnel
A fuse at the construction
site distribution board has
tripped
Check fuses
Cutting blade wobbles Blade tension is poor Return the cutting blade Manufacturer
Segments are coming o Overheating, cooling is
poor
Check cooling water line Operating personnel
Segments are soldering on Manufacturer
TROUBLESHOOTING TABLE
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat T-4010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat T-4010 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info