816509
16
Zoom out
Zoom in
Previous page
1/28
Next page
16 NMH0321CA
10-04-2015
(underground!), pipes and steel reinforcement in the
work area. Do not use electric power tools in the pre-
sence of in ammable liquids/gases or in humid (rain)
conditions.
Mount accessories and tools in the right way to pre-
vent them from coming loose. Check if all keys and
adjusting wrenches are removed from the machinery
before turning it on. Keep proper footing and balance
at all times.
MAIN COMPONENTS
The numbering of the illustrated product features refers to
the representation of the drill stand on page 2.
1. Quick-clamping column
2. Tensioner
3. Column
4. Quick mounting adapter
5. Lever
6. Lever
7. Carriage
8. Column
9. Carriage
10. Base
11. Hinge
12. Stabilisation bar
13. Levelling screw
14. Stabilisation bar
15. Transport wheels
16. Levelling screw
17. Base
DISPOSAL
Separate collection. This product must not be
disposed of with normal household waste. The
drill stand, accessories and packaging should
be sorted for environmental-friendly recycling.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
(S-3010) is in conformity with the following standards or
standardized documents:
EN 12348; 2006/42/EC
Director
C.J. van Beek
10.06.2011
CARAT Nederland BV, Nikkelstraat 18, NL-4823 AB, Breda
WARNING! Under no circumstances may
the design of the machine be modi ed wit-
hout the permission of the manufacturer.
Always use genuine accessories. Non-aut-
horized modi cations and/or accessories
can result in serious personal injury or the death of the
operator or others.
SAFETY INSTRUCTIONS
Read all safety warnings and instructions
that were provided with the drill stand or
the drill. Failure to follow the safety warn-
ings and the instructions may result in
electric shock, re and/or serious injury.
Save all safety warnings and instructions for future
reference.
Prevent dripping, leaking or unintentional uncoupling
of water hoses. Pay attention to the cooling water
during drilling overhead. Remove cooling water in a
safe way, for instance with a vacuum-cleaner. Keep
electric cables, plugs etc. dry.
Watch what you are doing. Use common sense. Do
not operate machinery when you are tired or not con-
centrated. Make sure that you can always stop the
motor (emergency stop). Do not use the machinery
of which the ON/OFF switch does not work properly.
Do not wear loose clothing or jewellery. They can
be caught in moving parts. When working in open
air rubber gloves and non-skid footwear are recom-
mended. Wear protective hair covering to contain
long hair.
Wear a helmet against falling parts, gloves for pro-
tection against sharp items and a safety goggle for
protection against sparks/small concrete particles.
Use a dust mask covering mouth and nose if nec-
essary. Ear protectors are recommended for sound
levels over 80 dB(A). For sound levels over 90 dB(A)
ear protectors are compulsory.
Disconnect the plug from the power source before
making any adjustments or changing accessories.
Starting drills accidentally is the cause of some ac-
cidents.
Do not overload the drill rig and do not use it as a lad-
der or scaffold. Overloading or standing on the drill
rig can raise the drill rig’s centre of gravity and cause
it to tip over.
Keep machinery tools sharp and clean for better and
safer performance. Follow maintenance instructions.
Keep handles dry and free from oil and grease.
Check for alignment and binding of moving parts.
Breakage of parts and any other conditions that may
affect the normal use of the machinery. A guard or
parts that are damaged should be properly repaired
or replaced by an authorised service centre.
The use of accessory and attachment other than
recommended in this manual or the catalogue may
present a risk of physical injury.
Have your drill stand serviced/repaired only by a
quali ed repair person using original replacement
parts. This will ensure that the safety of the device
is maintained.
Cluttered areas invite injuries. Do not let uninvited
persons or animals contact machinery or enter the
work area. Make provisions to catch loose concrete
parts/cooling water when drilling in storey oors or
roofs. When not in use, machinery must be stored in
a dry, locked-up place, out of the reach of children.
Keep work area clean. Pay attention to all cables
ENGLISH – ORIGINAL INSTRUCTIONS
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat S-3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat S-3010 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info