816479
76
Zoom out
Zoom in
Previous page
1/80
Next page
76
Errormessage/error Possiblecause Troubleshooting Personnel
High segment wear! Segment bonding is too so Use cutting wheels with harder seg-
ments or reduce feeding -pressure
Operating personnel
Segments are too thin in rela-
tion to the mo¬tor¬ capacity
and feeding pressure
Reduce the feeding pressure, or
use cutting wheels with thicker
segments
Segment number is too small Use cutting wheels with segments,
or reduce the feeding pressure
The cutting wheel runs out Use a new cutting wheel, have
the old one straightened, check
the cutting sha, use a new one if
necessary
The cutting wheel deviates Check the table guides, replace if
necessary
Abrasive aggregates Use cutting wheels with harder
segments
Feeding pressure is too high Reduce the feeding pressure
Cutting blade shows side
and radial run-out
Cutting blade is bent or
damaged
Have the cutting blade straightened,
solder the segments to a new blade
or use a new blade
Manufacturer
Flange is polluted or
damaged
Clean or replace the flange Operating personnel
Motor sha is bent Replace the electric motor Qualified electricians
Zero performance when
cutting, cutting blade
is blunt
The cutting blade does not
match the material
Use a proper cutting blade Operating personnel
The cutting blade does not
match the machine capacity
The cutting blade is too hard
Diamond on the segment
are blunt
Sharpen Specialist personnel
Suboptimal blade course Blunt segments Sharpen Specialist personnel
Cutting blade is overloaded Use an appropriate cutting blade Operating personnel
Poor tension of cutting blade Return the cutting blade Manufacturer
Mounting bore of the
cutting blade is worn out
The cutting blade rotates on
the motor sha
Check the mounting flange,
replace if necessary
Manufacturer
The mounting bore must be hol-
lowed out and a ring fitted in
Specialist personnel
The cutting blade is
oxide-coated
The cutting blade is overheat-
ing, too little cooling water
Check the cooling water¬ Operating personnel
Lateral friction in the cut Lower the feed rate, pull the -mate-
rial ¬slowly
Cracks on steel core;
eccentrical wear of the
cutting blade
The cutting blade is too hard Use a soer cutting blade Operating personnel
Motor sha bearing Replace the motor sha bearing
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat MultiCoup 350 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat MultiCoup 350 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 14.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info