816452

Carat CARACOUP 104 Manual

23
Zoom out
Zoom in
Previous page
1/92
Next page
23
ENGLISH
washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)
and the nuts (4x M8 ISO 4032).
Mounting the extension table
If you want to work with the extension table, proceed as
follows:
Insert the extension table into the lateral grommets on the
base frame and tighten it with the star grip screws
5.4 Fill the water tank
The water tank must be lled before the machine is
started. Use clear, clean water for this.
ATTENTION!
The water pump may not run without water,
otherwise it can be damaged.
. OPERATION
6.1 Intended working position of the operator
The operator takes position in front of the machine near
the switch and the chain driven handwheel to be able to
slide the cutter head with the handwheel and to press the
red stop button at any time.
6.2 Start-up preparation
To safely use the machine as intended, the following
preconditions must be met:
- The machine stands rmly.
- The water tank is lled with clean, clear water.
- The machine has been checked for damage, loose screw
connections and integrity.
- The water supply is functional.
- Rotation direction arrows on the cutting wheel and guard
match.
- An appropriate cutting wheel must be installed, which
meets optimum conditions.
- Lock the legs when the machine is on.
6.3 Start-up
The machine is switched on by the main switch. For this
purpose, press the green button to start
Aer the start, check the following:
The cooling water must be pumped to the cutting wheel
by the water pump in the suicient quantities and drain o
on both sides. If this is not the case, stop the machine im-
mediately! The motor is equipped with thermal insulation
activated when the temperature rises too high.
Wait approx. 30 minutes before restarting the machine
until the motor cools down
6.4 Cutting operation
6.4.1 Normal cutting in 90° position
When cutting in 90° position, the cutter head remains at a
xed point. For adjustment, proceed as follows:
1. Switch o the machine -> the cutting wheel must stop
rotating!
2. Loosen the adjusting screw.
3. Set the cutter head in the desired position.
4. Tighten the adjusting screw -> check if the cutter head is
adjusted in height and make sure that it cannot move.
5. Put the material to be cut onto the table (for table saw
machine position it directly at the material stop).
6. Check the position of the material using the angle stop.
7. Start the motor and the water pump and open the water
tap.
8. Grab the cutter head’s chain driven hand crank with the
right hand and the transport handle on the frame with
the le hand.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat CARACOUP 104 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat CARACOUP 104 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 3.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info