816453
43
Zoom out
Zoom in
Previous page
1/47
Next page
8584
Error message / error Possible cause Troubleshooting Personnel
When switched on, the
machine does not start
Mains plug is loose Check proper connection to
mains
Operating personnel
Mains plug is defective Check the mains plug
for operability, replace if
necessary
Qualied electricians
Loose connection in the
electric system
Have the entire electric
system of the machine
checked
The drive motor is
defective
Have the drive motor
checked, replace if necessary
The main switch is
defective
Have the main switch
checked, replace if
necessary.
The machine does
not provide suicient
performance
The mains plug is too
long, cord reel is wound
up
Observe the prescribed
length of the mains plug .
Unwind the cable cord
Operating personnel
Capacity of the local mains
is insuicient
Pay attention to and observe
the ma chine connection data
The drive motor does
not maintain the rotation
speed
Have the drive motor
checked, replace if necessary
Qualied electricians
Low or no cooling water
feed
The water pump sucks air Fill the tank with water;
swivel the pump with the
suction side downwards
Operating personnel
Hose are clogged Clean the hoses
Hoses bent Check hose layout
A hose is leaky or
detached
Replace or re-attach the hose
properly
The water pump wheel or
strainer is polluted
Clean the pump wheel or
strainer
Water pump does not
function
Have the electric supply line
checked, replace if necessary
Qualied electricians
Motor does not start Mains plug is not properly
plugged.
Check the mains plug for
proper connection
Operating personnel
A fuse at the construction
site distribution board has
tripped
Check fuses
Cutting blade wobbles Blade tension is poor Return the cutting blade Manufacturer
Segments are coming o Overheating, cooling is
poor
Check cooling water line Operating personnel
Segments are soldering on Manufacturer
TROUBLESHOOTING TABLE
Error message / error Possible cause Troubleshooting Personnel
High segment wear! Segment bonding is
too so
Use cutting wheels with
harder seg ments or reduce
feeding pressure
Operating personnel
Segments are too thin
in relation to the mo tor
capacity and feeding
pressure
Reduce the feeding
pressure , or use cutting
wheels with thicker
segments
Segment number is too
small
Use cutting wheels with seg-
ments, or reduce the feeding
pressure
The cutting wheel runs
out
Use a new cutting
wheel , have the old one
straightened , check the
cutting sha , use a new one
if necessary
The cutting wheel
deviates
Check the table guides,
replace if necessary
Abrasive aggregates Use cutting wheels with
harder seg ments
Feeding pressure is too
high
Reduce the feeding pressure
Cutting blade shows side
and radial run-out
Cutting blade is bent or
damaged
Have the cutting blade
straightened, solder the
segments to a new blade or
use a new blade
Manufacturer
Flange is polluted or
damaged
Clean or replace the ange Operating personnel
Motor sha is
bent
Replace the electric motor Qualied electricians
Zero performance when
cutting, cutting blade is
blunt
The cutting blade does
not match the material
Use a proper cutting blade Operating personnel
The cutting blade does
not match the machine
capacity
The cutting blade is too
hard
Diamond on the segment
are blunt
sharpen Specialist personnel
Suboptimal blade course Blunt segments sharpen Specialist personnel
Cutting blade is
overloaded
Use an appropriate cutting
blade
Operating personnel
Poor tension of cutting
blade
Return the cutting blade Manufacturer
Mounting bore of the
cutting blade is worn out
The cutting blade rotates
on the motor sha
Check the mounting ange,
replace if necessary
Manufacturer
The mounting bore must
be hollowed out and a ring
tted in
Specialist personnel
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat CARACOUP 100 ALU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat CARACOUP 100 ALU in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info