816453

Carat CARACOUP 100 ALU Manual

12
Zoom out
Zoom in
Previous page
1/47
Next page
23
ENGLISH
22
There are the following symbols and information signs on
the machine that refer to potential dangers:
Warning of rotating tool!
Running direction of the
saw blade
Wear gloves. Wear ear
protectors. The machine
meets EU guideline.
Observe the operating
manual. Wear protective
goggles
Laser
Class 2
635 mm
DO NO T
STARE
INTO
BEAM
ATTENTION
Rotation direction
3. MACHINE DATA
3.1 Diamond blades
DANGER!
Risk of injury by defective or incorrectly mounted
diamond blades!
Wrong rotation direction and damaged diamond blades
may cause injuries of personnel! Check diamond blades
for broken o segments and segment pieces, segment
foot cracks, diamond blade deformations or signs of
wear before starting work. Pay attention to the rotation
direction arrows on the diamond blades and guard!
DANGER!
Risk of injury by unchecked or unapproved tool!
Diamond blades or buzz saw blades that have not been
checked or approved may cause injuries of personnel!
Before starting work, check whether a proper diamond
blade is mounted. Pay attention to the rotation direction
arrows on the diamond blade and guard!
NOTE!
All diamond blades used must be designed in
terms of their permissible max. cutting speed to match
the max. drive speed and intended application of the
machine tool
Diamond blade Diameter Material
Carat tile and
natural stone
diamond blade
Ø 200
mm
Tile, ceramic,
stoneware, natural
and articial stone,
thin granite
3.2 Type plate
The type plate is located on the base frame of the machine
tool.
3.3 Installation site requirements
The oor surface must:
- Have suicient load bearing capacity.
- Be slip proof.
- Be level.
3.4 Storage requirements
Storage conditions
As a matter of principle, the machine, its components,
assemblies or parts must be only stored in the following
conditions:
do not store outdoors. store in dry and dust-free place.
do not expose to aggressive media. protect from
solar radiation. avoid mechanical vibrations. storage
temperature range 5 to 45°C
relative air humidity, max. 60%. In case of storage for
over 3 months, check general condition of all parts and
packaging on a regular basis. If necessary, renew or replace
conservation materials.
4. TRANSPORT
ATTENTION!
Damage through improper transportation!
Improper transportation can result in considerable
damage of the machine and objects in the vicinity.
Before every transport:
- The cutter head must be locked.
- The cutter head must be lowered and locked.
- The cutting table must be secured by the table lock
(for table saw machines).
- The machine must be disconnected from power supply.
Due to two transport rollers, the machine can be
transported by one or two persons who can use transport
handles.
Instruction of using crane liing eyes
The machine is designed for crane transport by means of
the liing eye.
Always check the tighteness of the liing eyes before using
it to transport the machine. To avoid damage, also check
that the liing straps do not touch the motor when liing.
CAUTION!
Risk of injury due to improper handle when it is
transported by crane.
CAUTION!
Risk of injury by standing under the machine when
it is transported by crane.
CAUTION!
Risk of injury of falling material from the working
table, it is not allowed to have any material on working
table when it is transported.
Crane liing eyes P-3510 / P-3512 / CARACOUP 104 ALU /
CARACOUP 100 ALU
5. INSTALLATION
5.1 Connection
Before connecting the machine to the power source,
make sure that:
- Voltage / phase of the power supply, match the date on
the type plate of the motor and machine.
- The power supply line is grounded according to the safety
provisions.
- The wire size of the extension cord is suicient, H07RNF
3x2.5 mm² up to 50m for 230V.
5.2 Mounting a diamond blade
To mount a new diamond blade or replace the used one,
proceed as follows:
1. Switch o the machine and interrupt the power supply
by pulling the mains cable from the mains outlet.
2. Loosen the screws on the diamond blade guard so as to
be able to remove the front half of the diamond blade
guard.
3. Loosen the nut of the motor sha and remove the outer
cutter ange.
4. Clean the cutter ange, nut and motor sha.
5. Check the parts for signs of wear.
6. Mount or replace the diamond blade. While doing so,
pay attention to the correct rotation direction of the
diamond blade and motor sha.
7. Replace the outer cutting ange on the motor sha.
8. Screw the nut onto the motor sha again and tighten it
rmly.
9. Replace the front half of the cutting wheel guard to
connect it with the rear half.
10. Tighten rmly the screws on the cutting wheel guard.
NOTE!
The arrow on the cutting wheel indicates
correct rotation direction.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
5.3 Mounting the transport handles and wheels
Mount the transport handles at the appropriate places on
the base frame using the supplied washers (4x A8,4 ISO
7089) and the screws (4x M8x30 ISO 4017), the spring wash-
ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).
Do the same with the transport wheels. Mount the trans-
port wheels at the appropriate places on the base frame
using the supplied washers (4x A,8,4 ISO 7090), the spring
washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)
and the nuts (4x M8 ISO 4032).
Mounting the extension table
If you want to work with the extension table, proceed as
follows:
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Carat CARACOUP 100 ALU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Carat CARACOUP 100 ALU in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish as an attachment in your email.

The manual is 4.04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info