543013
87
Zoom out
Zoom in
Previous page
1/206
Next page
87
Recording
3
b Synchronizing with an External
Device
Using a Reference Video Signal
(Genlock Synchronization)
When a reference sync signal (analog blackburst or tri-level signal) is input
through the GENLOCK terminal, the phases of the camcorder's V and H
sync will automatically be synchronized to it. The phase difference
between the external Genlock signal and the camcorder is initially set to
0. The H phase can be adjusted within the range of approximately ±0.4 H
(HD equivalent).
1 Open the [Genlock] submenu.
[J Other Functions] [Genlock]
2 Adjust the phase to the desired level and then press SET.
Using a Time Code Signal
An external SMPTE-standard LTC timing signal received from the TIME
CODE terminal will be recorded as the time code. The user bit of the
external timing signal can also be recorded. Before connecting the
device, set the TIME CODE terminal to input. Also, you must set the
running mode of the time code to [Free Run] (0 82).
1 Open the [TC In/Out] submenu.
[L TC/UB Setup] [Time Code] [TC In/Out]
2 Select [In] and then press SET.
Recording the User Bit of an External Signal
The user bit of an external time code signal can also be recorded with the
time code itself.
1 Open the user bit [Rec Mode] submenu.
[L TC/UB Setup] [User Bit] [Rec Mode]
2 Select [External] and then press SET.
NOTES
The Genlock signal synchronization stabilizes after approximately
10 seconds.
Genlock synchronization is possible even when a standard definition
Genlock signal is input. However, Genlock synchronization is not
possible when the camcorder’s video configuration is 1080i and the
input signal is 720P.
Operating modes:
[J Other Functions]
[Genlock]
[L TC/UB Setup]
[Time Code]
[TC In/Out]
[In]
Operating modes:
[L TC/UB Setup]
[User Bit]
[Rec Mode]
[Internal]
COPY
87


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon XF 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon XF 300 in the language / languages: English as an attachment in your email.

The manual is 12,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon XF 300

Canon XF 300 User Manual - German - 226 pages

Canon XF 300 User Manual - Dutch - 218 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info