683281
53
Zoom out
Zoom in
Previous page
1/178
Next page
[Camera] Setting Initial Camera Settings and External Device Name
53
5
Setting Page
Camera Control
(1) [Digital Zoom]
Set digital zoom to [Disable] or [Enable].
The higher the digital zoom ratio, the lower the image
quality becomes.
(2) [Image Stabilizer]
Select [Disable], [On1] or [On2] for image stabilizer.
Image stabilizer has the effect of correcting blurry
images. Try [On2] if the image is still blurry after
selecting [On1].
If you have selected [On1] or [On2] as the image
stabilizer setting, the viewing angle will be smaller and
the image more coarse than when [Disable] is
selected. This is not a malfunction.
(3) [AGC Limit]
Select one of 5 levels from 1 to 5 to automatically set
the upper gain limit. The greater the value, the higher
the sensitivity becomes. If you do not want to use the
automatic gain adjustment, select [OFF]. Setting the
[AGC Limit] allows you to record with reduced noise
when recording in low light conditions.
Day/Night
(1) [Mode]
Set Day/Night mode to [Manual] or [Auto].
It is also possible to switch between [Day Mode] and
[Night Mode] using Admin Viewer Night Mode
function (p. 141).
If you have selected [Auto], set [Switching Brightness]
and [Response (sec.)] according to the environment
in which the camera is installed as well as the desired
switching conditions.
(2) [Switching Brightness]
Set the brightness at which Day Mode and Night
Mode will be switched when [Auto] is selected in
[Mode]. Select [Darker], [Slightly Darker], [Standard],
[Slightly Brighter] or [Brighter]. Select [Darker] if you
want to capture video in color as much as possible.
Select [Brighter] to reduce noise. Note that this mode
switches to black & white sooner.
(3) [Response (sec.)]
Set the time in seconds needed for judgment on
switching between Day Mode and Night Mode when
[Auto] is selected in [Mode]. Select [60], [30], [20],
[10] or [5].
The mode will switch between Day Mode and Night
Mode if brightness remains above or below the level
set in (2) for the number of seconds specified.
Select [30] or [60] if brightness changes frequently,
such as when a light source passes in front of the
camera. Select [5] or [10] if change in brightness is
minimal.
Degree of
blurriness
corrected
Viewing angle
ratio
Effective
pixels
Disable 100%
Approx. 2.07
megapixels
On1 Small 83%
Approx. 1.44
megapixels
On2 Large 50%
Approx. 0.52
megapixels
Important
If [On2] is selected, it is best to select a video size smaller
than “960 x 540”.
The image stabilizer is not effective when the subject is
shaking.
The image stabilizer is not effective beyond a certain level of
vibration or against momentary vibration.
See “Important” on p. 94, p. 100 for precautionary notes
regarding Admin Tools configuration when image stabilizer is
set.
See “Important” on p. 136 for precautionary notes regarding
the Viewer when image stabilizer is set.
[AGC Limit] is disabled when [Exposure] is set to [Manual] or
[Auto (Flickerless)] in the Admin Viewer.
Minimum subject illumination may change when [AGC Limit]
is set.
Important
If [Auto] is selected for [Day/Night], conduct a thorough
operation test to check the effectiveness of the setting
beforehand.
If [Auto] is selected for [Day/Night], set [Exposure] of the
Admin Viewer to [Auto], [Auto (Flickerless)] or [Auto (Shutter-
priority AE)] (p. 140).
To use with infrared illumination, set [Day/Night] to [Manual].
When Day/Night Mode is set to [Manual], in additional to the
Day/Night function of the Admin Viewer (p. 141), it is also
possible to switch Day/Night Mode via settings in [Setting
Page] > [Event] > [External Device Input] (p. 65) or [Event] >
[Timer] (p. 66).
When [Day Mode] and [Night Mode] are switched, the image
may not focus correctly depending on the brightness.
If [Day/Night] is set to [Auto], the infrared cutoff filter may
move several times while the mode is switching between
[Day Mode] and [Night Mode]. Pan, tilt, zoom and manual
focus will not work during this period.
53


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon VB-H610VE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon VB-H610VE in the language / languages: English as an attachment in your email.

The manual is 8,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon VB-H610VE

Canon VB-H610VE Installation Guide - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info