596283
16
Zoom out
Zoom in
Previous page
1/19
Next page
7.
Troubleshooting
Page
24
27
29
28
25
33
26
:3
1
28
28
28
-
24
Problem
Soon after
thc power is turned
on, the indicator
lamp turns on'
Although the
5
icon is lit in
the viewfinder,
the slave does
not fire.
The flash picture cnmc out
undrrexposed
The slave d~~cs nclt fire evcn
when the sl~utt<.~.
i,
~rrlra.;ed.
The ST-EP does not enlit th<.
XF-assist beam.
The slave's flash-rcady indica.
tor (blinking AF
-
assist beam
I
turns off.
The test transmission
does not
work.
The flash
ratlo cannot be set.
Probable Cause
If the power is turned on and the ST-E2 is not
used for
90
scc., the power turns off automatically.
The
5
]con in the v~ewfinder does not indicate
flash ready. Rather. it indicates that the ST-E2 is
able
to
transm~t.
The flash ratio control lamp was lit even thouph a
multi
-
flash system with flash ratio settings was
not used.
'The subject is beyond the effective flash range.
'I'hc sl~ivr's channel does not lnatcli the ST-E2's
oh;~nnrl.
Tl~r sl;~ve is
tor^
far away from thc ST-E2.
'Thu sl;~vc is
r~r,
tl~r
side
or hack of thr c:lmr,r;l.
'l'hc
Speedlite's
slave
sr,nsar
IS
not pmperly point
-
c.d
3t
L~C
ST-E2.
'l'hc Ilr~sh ratio h:lu Ihcrr~ srt, hut thc slave ID has
hrrn set to
C.
1'Iic,
r;~rner;l is not
;II~
KOS-3.
The, sla\.e is in the SE mode.
You prcssrd the shutter button halfway and this
activ;~ted the exposure meter
Thr camera is not an EOS
-
3.
The
ST-E2's main switch is set to
<HOLD>.
Solution
Either
press the shutter button halfway or press
the
<
PILOT
>
button.
When
the slave is ready to fire,
~ts
A12-assist beam
emltter blinks
Turn off the flash ratio control lamp
bcforc takinp
the
picturr~.
Place the slave nearer to the suhect or use
3
larg-
cr aperture (smaller f
-
number).
Set thr slavc to thesamechannel as thr ST-E2.
Position the slavc nearer to the ST-E2 :ind tcst
the transmission befirrc taking the picture.
Use On'-(:amera Shoe Cord
2
(solrl separatrlyl and
point the ST-E2's trtlnsmitter toward the slave.
Use thc
RSOEX's
bounce feature trl point its sI;~vc
sensor townrd the ST
-
EZ.
Set
thc slave
11)
to
A
or
B.
If thc
EOS
camcra has a built
-
in AF
-
assist beam.
the camera will rmit the beam instead ofthe ST-
E2.
Press the ST-E2's
<
PILOT
>
button to cancel the
slave's
SE mode.
Make sure the metering display in the viewfinder
is
off Then test the transmission.
The flash ratio cannot he set with cameras other
than the EOS
-
3.
Set the main switch to
<
I
1.
COPY
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon Speedlite Transmiter ST-E2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon Speedlite Transmiter ST-E2 in the language / languages: English as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info