542910
20
Zoom out
Zoom in
Previous page
1/274
Next page
9
1
2
L K
J
17
1. Installare il coperchio della testina (J).
2. Chiudere il coperchio superiore.
3. A
ttendere circa 20 minuti finché la spia ALIMENTAZIONE (POWER) (bianca)
(K) non lampeggia più e rimane fissa, quindi andare al passaggio successivo.
Q
uesta operazione è necessaria per rendere la stampante pronta per luso.
Non spegnere la stampante fino a quando la spia ALIMENTAZIONE
(POWER) rimane accesa.
La stampante potrebbe emettere rumori durante la preparazione alla stampa. Tali rumori fanno parte
del normale funzionamento della stampante.
Se la spia di Allarme (Alarm) (arancione) (L) lampeggia, assicurarsi che la leva di bloccaggio
della testina di stampa sia chiusa correttamente. Aprire la leva di collegamento e la leva di
bloccaggio della testina di stampa, quindi ricominciare da
.
Quando la stampante viene accesa per la prima volta, viene utilizzato inchiostro per prepararla
alla stampa. È possibile controllare il livello dell’inchiostro rimasto dal driver della stampante
(Windows) o dalla Canon IJ Printer Utility (Mac) dopo l’installazione del software.
1. Bringen Sie die Abdeckung für den Kopf (J) an.
2. Schließen Sie die obere Abdeckung.
3. W
arten Sie etwa 20 Minuten, bis die POWER-Lampe (weiß) (K) nicht mehr
blinkt, sondern kontinuierlich leuchtet, und fahren Sie dann mit dem nächsten
Schritt fort.
D
ieser Vorgang ist erforderlich, um den Drucker einsatzbereit zu machen.
Schalten Sie den Drucker erst aus, wenn die POWER-Anzeige
kontinuierlich leuchtet.
hrend der Vorbereitung auf das Drucken gibt der Drucker möglicherweise Betriebsgeräusche von
sich. Dies ist vollkommen normal.
Wenn die Alarm-Anzeige (orange) (L) blinkt, überprüfen Sie, ob der Sperrhebel für den
Druckkopf ordnungsgemäß geschlossen ist. Öffnen Sie den Winkelhebel und den Sperrhebel
für den Druckkopf, und
beginnen Sie erneut bei
.
Beim ersten Einschalten des Druckers wird Tinte verbraucht, um den Drucker auf das Drucken
vorzubereiten.
Der verbleibende Tintenstand kann über den Druckertreiber (Windows) oder das
Canon IJ Printer Utility (Mac) nach der Softwareinstallation überprüft werden.
1. Installez le capot des tes (J).
2. Fermez le capot supérieur.
3. A
ttendez environ 20 minutes que le voyant ALIMENTATION (POWER) (blanc)
(K) cesse de clignoter et reste allumé, puis passez à l’étape suivante.
C
ette opération est nécessaire pour préparer limprimante. Ne mettez pas
l’imprimante hors tension tant que le voyant ALIMENTATION (POWER) ne
reste pas allumé.
L’imprimante peut émettre des bruits de fonctionnement lorsquelle se prépare à imprimer. Ceci est
normal.
Si le voyant Alarme (Alarm) (orange) (L) clignote, vériez que le levier de verrouillage de tête
d’impression est correctement abaissé. Relevez le levier mixte et le levier de verrouillage de
tête d’impression, puis reprenez à partir de l’étape
.
Lorsque vous mettez l’imprimante sous tension pour la première fois, de l’encre est utilisée
pour la préparer à l’impression. Vous pouvez vérier le niveau d’encre restant à partir du pilote
d’imprimante (Windows) ou Canon IJ Printer Utility (Mac) après avoir installé le logiciel.
1. Install the Head Cover (J).
2. Close the Top Cover.
3. W
ait for about 20 minutes until the POWER lamp (white) (K) stops flashing and
stays lit, then proceed to the next step.
T
his operation is required to make the printer ready for use. Do not turn off the
printer until the POWER lamp stays lit.
The printer may make some operating noises when preparing to print. This is normal operation.
If the Alarm lamp (orange) (L) ashes, make sure that the Print Head Lock Lever is closed
correctly. Open the Joint Lever and Print Head Lock Lever, then start again from
.
When the printer is turned on for the rst time, ink is used to ready the printer for printing. The
remaining ink level can be checked from the printer driver (Windows) or Canon IJ Printer Utility
(Mac) after software installation.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon Pixma Pro 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon Pixma Pro 1 in the language / languages: All languages as an attachment in your email.

The manual is 22,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon Pixma Pro 1

Canon Pixma Pro 1 Installation Guide - English - 4 pages

Canon Pixma Pro 1 Installation Guide - German - 4 pages

Canon Pixma Pro 1 Installation Guide - Dutch - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info