709683
109
Zoom out
Zoom in
Previous page
1/116
Next page
103
Appendix
Canon LX-MU800Z / LX-MU600Z User Commands
Interface and Requirements (Ver 1.0)
Serial (RS-232) Interface
The RS-232 Commands use only ASCII characters which can be entered using a typical terminal
emulator like Windows HyperTerminal with the following setting:
Bits per second: 9600 bps
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
Note that each input character will be echoed on the terminal by MCU and there is no need to set the
local echo “ON” with the terminal setting.
TCP/IP Interface
The operation commands are available through telnet protocol. See page 75 for setting.
Serial and TCP/IP Interface over HDBaseT
Serial bits per second setting is xed to 9600 over HDBaseT. The other settings are same as above.
System Operation Commands
The operation commands tell the projector what to do. All commands start with 2 letters: “op” for
operations commands, and a space [SP] then following a control command then nally the value wants
to read, set, increase or decrease. All commands must end with a carriage return (ASCII hex 0D),
shown as [CR] below. The syntax for operations commands is as follows:
op[SP]<operation command>[SP]<Setting Value>[CR]
For all but Execute functions the response from the projector will be the command and “= <value>”
where <value> is the current value or “NA” if the value is not available. For execute functions the
response will be the same command. All responses will be in CAPS. Please refer to the following table
for command list and examples:
System Operation Command
Operation Commands Values
Set = <value> Makes the unit take that value.
Get ? Asks what the current value is.
Increment + Adds 1 to the current value.
Decrement - Subtracts 1 from the current value.
Execute (none) Performs an action such as a reset.
Get operations command example:
Input: op bright ? [CR]
System response: OP BRIGHT = 100
Increase & Decrease operations command examples:
Input: op bright + [CR]
System response: OP BRIGHT = 101
Input: op bright - [CR]
System response: OP BRIGHT = 126
Set operations command example:
Input: op bright = 127 [CR]
109


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon LX-MU600Z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon LX-MU600Z in the language / languages: English as an attachment in your email.

The manual is 27,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon LX-MU600Z

Canon LX-MU600Z User Manual - German - 117 pages

Canon LX-MU600Z User Manual - Dutch - 117 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info