615752
33
Zoom out
Zoom in
Previous page
1/77
Next page
33
ENGLISH
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 1
rear adjuster foot. These adjusters change the image height and
projection angle. To adjust the projector:
1. Press the quick-release button and lift the front of the projector.
Once the image is positioned where you want it, release the
quick-release button to lock the foot in position.
2. Screw the rear adjuster foot to fine tune the horizontal angle.
To retract the foot, hold up the projector while pressing the quick-
release button, then slowly lower the projector. Screw the rear
adjuster foot in a reverse direction.
If the projector is not placed on a flat surface or the screen and the
projector are not perpendicular to each other, the projected image
becomes trapezoidal. To correct this situation, see "Correcting
keystone" on page 34 for details.
Do not look into the lens while the lamp is on. The strong
light from the lamp may cause damage to your eyes.
Be careful when you press the adjuster button as it is close
to the exhaust vent where hot air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do
this, press AUTO PC on the projector or remote control. Within 3
seconds, the built-in Intelligent Auto Adjustment function will re-
adjust the values of Frequency and Clock to provide the best picture
quality.
The current source information will be displayed in the upper left
corner of the screen for 3 seconds.
The screen will be blank while AUTO PC is functioning.
This function is only available when a PC signal (analog
RGB) is selected.
Fine-tuning the image size and clarity
For adjusting the size to your desired, you need to move the
product for appropriate projection distance because of small Zoom
ratio. Follow the procedure below for the installation and
adjustment.
The focus will be off after adjusting the zoom, so be sure to
readjust the focus. If the image is very blurry, adjusting the focus to
make the image sharp will change the size of the projected image.
Repeat the zoom and focus adjustments in alternation as necessary.
In the right figure, (A) Focus Ring, (B) Zoom Ring
1. Adjust Zoom. (using (B) Zoom Ring)
2. For the short distance/large screen, dial the ring fully to Wide
end. For the long distance/small screen, dial the ring fully to
Tele end.
3. Adjust Focus. (using (A) Focus Ring)
4. Move the product back and forth to adjust the screen size.
5. Adjust Focus again if necessary.
2
1
B
A
Tele
Wide
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon LV-S300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon LV-S300 in the language / languages: English as an attachment in your email.

The manual is 5,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon LV-S300

Canon LV-S300 User Manual - German - 82 pages

Canon LV-S300 User Manual - Dutch - 79 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info