Common Problems & Solutons (→ "POWER/STATUS/LAMP Indicator" on page 72.)
ProblemCheck These Items
Does not turn on• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on. See
pages 23 and 24.
• Ensure that the lamp cover or the lamp is installed correctly. See page
71.
• Check to see if the projector has overheated. If there is insufficient ventilation around the projector or if the room where you are
presenting is particularly warm, move the projector to a cooler location.
• Check to see if you continue to use the projector for another 100 hours after the lamp has reached the end of its life. If so, re
-
place the lamp.
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• The lamp has reached the end of its usable life. Replace the lamp.
• Set [Fan mode] to [High altitude] when using the projector at altitudes approximately 5500 feet/1600 meters or higher. Using
the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [High altitude] can cause the
projector to overheat and the projector could shut down. Also the projector could not turn on due to the increased temperature
of the lamp after power off. If these happen, wait a couple minutes and turn on the projector.
• Also when the lamp is turned off, the projector internal temperature is hot. If the power is turned on before the projector has
cooled down, the fan will run a short time before the lamp will turn on.
• If any of the above is not the cause of the problem, turn off the main power and disconnect the power cord. After allowing 5
minutes, plug the power cord and turn on the main power.
Will shut down• Ensure that the Power management or Off timer is off. See page 62, 63.
No picture• Use the INPUT button to select your source. See page 26.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page
51.
• Remove the lens cover.
•
Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. See page 66.
• Enter your registered Password if the Password function is enabled. See page 38.
• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to
the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting
with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power man
-
agement software.
• See also the next page.
Picture suddenly becomes dark• Check if the projector is in the Forced cooling operation because of too high ambient temperature. If this is the case, lower the
internal temperature of the projector by selecting [High] for [Fan mode]. See page 61.
Color tone or Color balance is
unusual
• Check if an appropriate color is selected in [Screen color]. If so, select an appropriate option. See page
57.
• Adjust [Color balance] in [Adjustment]. See page
51.
Image isn’t square to the
screen
• Reposition the projector to improve its angle to the screen. See page
28.
• Use the Keystone correction function to correct the trapezoid distortion. See page
31.
Picture is blurred• Adjust the focus. See page 30.
• Reposition the projector to improve its angle to the screen. See page
28.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
11, 12, 80, 81.
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on. Should this hap
-
pen, let the projector stand until there is no condensation on the lens.
Picture is distorted• Make sure the VGA cable is connected.
• Press the AUTO PC button on the projector cabinet or the remote control. See page
34.
Flicker appears on screen• Set [Fan mode] to other mode than [High altitude] when using the LV-7375 at altitudes approximately 5500 feet/1600 meters or
lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [High altitude] can cause
the lamp to overcool, causing the image to flicker. Switch [Fan mode] to [Auto] or [High]. See page 61.
Image is scrolling vertically,
horizontally or both
• Use the INPUT button to select your source. See page
26.
• Adjust the computer image manually with the [Horizontal position] or [Vertical position] in the [Adjustment]
→
[Input signal].
See page 53.
Remote control does not
work
• Install new batteries. See page
9.
• Make sure there are no obstacles between you and the projector.
• Stand within 7 m (22 feet) of the projector. See page
9.
Indicator is lit or blinking• See the POWER/STATUS/LAMP Indicator on page 72.
Cross color in RGB mode• Press the AUTO PC button on the projector cabinet or the remote control. See page 34.
• Adjust the computer image manually with [Clock] or [Tracking] in [Input signal] in the menu. See page
52.
Whenever the projector is
turned on, a message prompt-
ing you to clean the filter will
be displayed
• Clean or replace the filter and then reset the Filter counter. See page
66, 67.
Press any button on the remote control or the projector cabinet to clear the message.
The projector is behaving in
an erratic way
• Turn off the main power and disconnect the power cord.
Allow 5 minutes and then plug the power cord and turn on the main power.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Canon lv 8300 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Canon lv 8300 in the language / languages: English as an attachment in your email.
The manual is 7,11 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
