475882
6
Zoom out
Zoom in
Previous page
1/83
Next page
6

Immediately turn the power off, unplug the projector,
and contact your dealer under the following
conditions, otherwise a fire or an electric shock may
result.
If smoke comes out from it.
If it emits a strange odor, or makes a strange noise.
If lamp goes out with a loud bang.
If water or any other liquid gets into it.
If metal or foreign objects get inside it.
If it is knocked down or dropped and the cabinet is
broken.

Follow the instructions below when using the power
cable, otherwise a fire, an electric shock, or injury
may result.
Do not place heavy objects on the power cord or
position the power cord under the projector. Doing
so may damage the power cord.
Do not run the power cord under a carpet. As it
goes unnoticed, excessive load may be applied on
the cord unintentionally.
Do not modify, bend forcibly, twist, or pull the power
cord.
Do not place the power cord near heat generating
equipment or heat it.
Do not bend, wind, or bind excessively the power
cord when using it.
Be sure to connect the projector to a grounded
outlet. Failure to do so may result in an electric
shock.
Do not continue to use a damaged power cord. If
the power cord is damaged, take it to your dealer
and have it replace.
Use only the supplied power cord.
Follow the instructions below when handling the
power plug or connector, otherwise a fire, an electric
shock, or injury may result.
Use the projector within the voltage range specified
on the projector (AC 100 V– 240 V).
Insert the power plug or connector into the power
outlet firmly. Do not use a damaged or loosen
power plug or connector.
Be sure to hold the power cord plug or connector
when disconnecting it from the power outlet. If the
power cord itself is pulled, it may be damaged.
Do not plug or unplug the power cord with wet
hands.
Disconnect the power cord from the power outlet
before cleaning the projector.
Do not stick metal objects into the electrical
contacts of the power plug or connector.
Follow the instructions below to install or handle the
projector. Otherwise, a fire, an electric shock, or injury
may result.
Do not touch the projector, power cord, or cables
when lighting begins.
Do not use the projector in a bathroom or shower
room.
Do not expose the projector to rain, snow, or use
near water.
Do not insert metal objects into the projector
through the air vents.
Do not place the containers with water on the
projector.
Do not install in the locations exposed to oily vapors
or smoke (e.g., near a cooking table or humidifier).
Before moving the projector, turn the power off and
disconnect the power cord and all cables.
Do not put spray cans in front of the exhaust
vent. When spray cans are exposed to heat, the
pressure in them will increase and explode.
Do not open nor remove the cabinet. There are
high voltage components inside the projector.
Contact your dealer for inspection, adjustment, and
service.
Do not attempt to disassemble the projector
(including expendable parts) or remote control unit.
Do not look into the lens while the projector is used.
Strong light may hurt your eyes. Be especially
careful that small children do not look into the lens.
When an extension cord is necessary, be sure that
the total current load of all equipment connected to
the extension cord does not exceed the specified
rating of the extension cord.
Periodically unplug the power cord and remove the
dust that builds up on the power cord or connector.
Follow the instructions below when handling the
batteries. Failure to do so may cause explosion, heat
generation, a fire, or leakage of the battery fluid.
Do not heat or disassemble the batteries, or throw
them into fire.
Do not attempt to recharge the batteries.
Follow the instructions below when the lamp is
replaced or breaks.
Always unplug the power cord before replacing the
lamp.
When the lamp breaks, shards of glass may
scatter in the lamp housing. Contact your dealer for
cleaning or inspecting the projector, or replacing
the lamp.





6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon LV-7295 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon LV-7295 in the language / languages: English as an attachment in your email.

The manual is 6,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canon LV-7295

Canon LV-7295 User Manual - German - 83 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info