Common Problems & Solutions (→ "Power/Status/Lamp Indicator" on page 61.)
ProblemCheck These Items
Does not turn on or shut
down
• Check that the power cord is plugged in and that the power button on the projector cabinet or the remote control is on. See
pages 23 and 24.
• Ensure that the lamp cover is installed correctly. See page
60.
• Check to see if the projector has overheated or the lamp usage exceeds 2100* hours (up to 3100* hours : Quiet mode). See
page 60. If there is insufficient ventilation around the projector or if the room where you’re presenting is particularly warm,
move the projector to a cooler location.
* LV-X7: 3100 hours (up to 4100 hours in Quiet mode).
• The lamp may fail to light. Wait a full minute and then turn on the power again.
• The lamp has reached the end of its usable life. Replace the lamp.
• When the lamp is turned off, the projector internal temperature is hot. If the power is turned on before the projector has
cooled down, the fan will run a short time before the lamp will turn on. If this happens, wait a couple minutes and turn on the
projector.
[LV-7365]
• Set [Fan mode] to [High altitude] when using the projector at altitudes approximately 5500 feet/1600 meters or higher. Using
the projector at altitudes approximately 5500 feet/1600 meters or higher without setting to [High altitude] can cause the
projector to overheat and the projector could shut down. Also the projector could not turn on due to the increased temperature
of the lamp after power off. If these happen, wait a couple minutes and turn on the projector.
[LV-7265/LV-7260/LV-X7]
• Select [High] in [Fan mode] if you use the projector at a high altitude or under low atmospheric pressure because LV-7265,
LV-7260, and LV-X7 do not have the [High altitude] option in [Fan mode]. Using the projector at a high altitude or under
low atmospheric pressure without setting to [High] can cause the projector to overheat and the projector could shut down.
Furthermore, the projector could not turn on due to the increased temperature of the lamp after power off. If these happen, wait
a couple minutes and turn on the projector.
Will turn off• Ensure that the Power Management or Off timer is off. See page 51, 52.
No picture• Use the INPUT button to select your source (LV-7365/LV-7265: Computer 1, Computer 2, Video or S-Video / LV-7260/LV-X7:
Computer, Video or S-Video). See page 26. If there is still no picture, press the button again.
• Ensure your cables are connected properly.
• Use menus to adjust the brightness and contrast. See page
46.
• Remove the lens cap.
•
Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. See page 55.
• Enter your registered Password if the Password function is enabled. See page 37.
• When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to
the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting
with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power man
-
agement software.
• See also the next page.
Picture suddenly becomes dark• Move the projector to a cooler location, or set [Fan mode] to [High].
Color tone or Color balance is
unusual
• Check if an appropriate color is selected in [Screen color]. If so, select an appropriate option. See page
48.
• Adjust [Color balance] in [Image adjustment]. See page
46.
Image isn’t square to the
screen
• Reposition the projector to improve its angle to the screen. See page
27.
• Use the Keystone correction function to correct the trapezoid distortion. See page
29.
Picture is blurred• Adjust the focus. See page 28.
• Reposition the projector to improve its angle to the screen. See page
27.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
12, 13.
• Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on. Should this hap
-
pen, let the projector stand until there is no condensation on the lens.
Picture is distorted• Make sure the VGA cable is connected.
• Press the AUTO PC button on the projector cabinet or the remote control. See page
31.
Flicker appears on screen• Set [Fan mode] to other mode than [High altitude] when using the LV-7365 at altitudes approximately 5500 feet/1600 meters or
lower. Using the projector at altitudes less than approximately 5500 feet/1600 meters and setting to [High altitude] can cause
the lamp to overcool, causing the image to flicker. Switch [Fan mode] to [Auto] or [High]. See page 52.
Image is scrolling vertically,
horizontally or both
• Use the INPUT button to select your source (LV-7365/LV-7265: Computer 1, Computer 2, Video or S-Video / LV-7260/LV-X7:
Computer, Video or S-Video). See page 26.
• Adjust the computer image manually with the [Horizontal position] or [Vertical position] in the [Display settings]. See page
47.
Remote control does not
work
• Install new batteries.See page
10.
• Make sure there are no obstacles between you and the projector.
• Stand within 7 m (22 feet) of the projector. See page
10.
Indicator is lit or blinking• See the POWER/WARNING/LAMP Indicator on page 61.
Cross color in RGB mode• Press the AUTO PC button on the projector cabinet or the remote control. See page 31.
• Adjust the computer image manually with [Clock] or [Tracking] in [Display settings] in the menu. See page
47.
Whenever the projector is
turned on, a message prompt-
ing you to clean the filter will
be displayed
• Clean or replace the filter and then reset the Filter counter. See page
55, 56.
Press any button on the remote control or the projector cabinet to clear the message.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Canon lv 7260 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Canon lv 7260 in the language / languages: English as an attachment in your email.
The manual is 9,77 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
