214647
67
Zoom out
Zoom in
Previous page
1/83
Next page
58
6. Maintenance
Replacing the Lamp
After your lamp has been operating for 2000*
1
hours (up to 3000*
1
hours in Quiet mode) or longer, the LAMP indi-
cator in the cabinet will blink red and the message Replace with the new lamp.”*
2
will appear. Even though the
lamp may still be working, replace it at 2000*
1
(up to 3000*
1
hours in Quiet mode) hours to maintain optimal projec-
tor performance. After replacing the lamp, be sure to clear the lamp counter. See page 55.
CAUTION
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 30 seconds, turn off the main power switch and then disconnect the power cord. Allow at least one hour
for the lamp to cool before handling.
DO NOT REMOVE ANY SCREWS except two lamp case screws. You could receive an electric shock.
Do not break the glass on the lamp housing.
Keep nger prints off the glass surface on the lamp housing. Leaving nger prints in the glass surface might
cause an unwanted shadow and poor picture quality.
The projector will turn off and go into standby mode after 2100
*
1
(up to 3100*
1
hours in Quiet mode) hours of
service. If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000*
1
hours (up to
3000*
1
hours in Quiet mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the
lamp case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer for
lamp replacement.
*
1
NOTE: Lamp life for LV-X7 is 3000 hours in Normal mode and 4000 hours in Quiet mode.
The projector will turn off and go into standby mode after 3100 (up to 4100 hours in Quiet mode) hours of service.
A lamp may burn out before the LAMP indicator blinks.
*
2
NOTE: This message will be displayed under the following conditions:
- for one minute after the projector has been powered on
- when the POWER button on the projector cabinet or on the remote control is pressed
To turn off the message, press any button on the projector cabinet or the remote control.
To replace the lamp:
IMPORTANT:
Follow the instructions described in this section.
The lamp component might have high voltage and heat. For safety, the lamp part is designed to prevent the
lamp cover from easily becoming detached.
Optional lamp and tools needed for replacement:
Replacement lamp LV-LP30 (LV-7365), LV-LP26 (LV-7265/LV-7260) or LV-LP27 (LV-X7)
Phillips screwdriver or equivalent
NOTE: The two lamp houses are slightly different in appearance.
The following explanation uses drawings for the lamp LV-LP26.
1. Placetheprojectoronasoftclothandturnitovertoaccessthelampcoveronthebottom.
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon lv 7260 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon lv 7260 in the language / languages: English as an attachment in your email.

The manual is 9,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info