214542
32
Zoom out
Zoom in
Previous page
1/74
Next page
23
3. Projecting an Image (Basic Operation)
Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
* If the projected image does not appear square to the screen then use the
Keystone feature for proper adjustment. See page 25 to 26.
Adjusting the Picture Size and Position
2
1
4
3
Adjustable Tilt Foot
Move the projector left to center the image horizontally on the screen.
Adjustable Tilt
Foot Lever
Adjust the Tilt Foot
1. Lift the front edge of the projector.
CAUTION:
Do not try to touch the ventilation outlet during Tilt Foot adjustment as it
can become heated while the projector is turned on and during its cool
down period after it is turned off.
2. Push and hold the adjustable tilt foot lock button on the front of the
projector to extend the adjustable tilt foot.
3. Lower the front of the projector to the desired height.
4. Release the adjustable tilt foot lock button to lock the adjustable tilt
foot.
There is approximately 10 degrees (up) of adjustment for the front of the
projector.
Adjusting the height of a projected image or changing projection angle will
run the Auto Keystone correction function to quickly correct the vertical
distortion. The "Keystone" screen will be displayed.
For operating the "Keystone" screen, see " Correcting Keystone Distortion"
on page 25.
5. The rear foot height can be adjusted up to 10 mm/0.4 inch.
Rotate the rear foot to the desired height in order to square the image on
the projection surface, but the vertical distance from the bottom to the desk
or floor should be 10 mm/0.4 inch to make the projector horizontal on the
flat surface.
NOTE: If you rotate the rear foot too much, it will come off from the bottom.
CAUTION:
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as using the tilt foot to carry or hang (from the wall or
ceiling) the projector can cause damage to the projector.
Rear Foot
Up
Down
NOTE: To fine-adjust the height of the rear foot, remove the factory attached spacer
and rotate the rear foot to the desired height. Do not throw away or lose the spacer.
Attach the spacer to the rear foot again after using the projector.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon lv 7255 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon lv 7255 in the language / languages: English as an attachment in your email.

The manual is 4,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info