19294
13
Zoom out
Zoom in
Previous page
1/33
Next page
3. REPAIR
3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
Service part
Notes on replacement
*1
Adjustment / settings Operation check
Logic board ass'y
QM2-1548
- Before removal of the logic board ass'y,
remove the power cord, and allow for
approx. 1 minute (for discharge of
capacitor's accumulated charges), to
prevent damages to the logic board
ass'y.
- Before replacement, check the waste
ink amount (by service test print or
EEPROM information print). If the
waste ink amount is 7% or more, also
replace the bottom case unit or the ink
absorbers when replacing the logic
board ass'y. See 3.3. Adjustment /
Settings, (6) Service mode, for details.
[See 3-3. Adjustment / Settings, (6)
Service mode, for details.]
After replacement:
1. Initialize the EEPROM.
2. Reset the waste ink counter.
3. Set the destination in the EEPROM.
4. Correct the CD-R and automatic print
head alignment sensors.
[See 3-3. Adjustment / Settings, (6)
Service mode, for details of 1 to 4]
5. Perform the print head alignment in
the user mode.
- EEPROM information print
- Service test print
- Printing via parallel or USB
connection
- Direct printing from a digital camera
Bottom case unit
QM2-1205
After replacement:
1. Reset the waste ink counter.
[See 3.3. Adjustment / Settings, (6)
Service mode.]
- Service test print
Ink absorber
QC1-4222 / 4223 / 4224 /
4263 / 4264 / 4864 / 4221 /
4257
Carriage unit
QM2-1209
At replacement:
1. Apply grease to the sliding portions.
[See 3
-3. Adjustment / Settings, (3)
Grease application.]
After replacement:
1. Correct the CD-R and automatic print
head alignment sensors.
[See 3.3. Adjustment / Settings, (6)
Service mode.]
2. Perform the print head alignment in
the user mode.
- Service test print (Confirm CD-R
and automatic print head alignment
sensor correction.)
Paper feed motor unit
QK1-0550
- The red screws securing the paper feed
motor are allowed to be loosened. (DO
NOT loosen any other red screws.)
At replacement:
1. Adjust the paper feed motor.
[See 3
-3. Adjustment / Settings, (1)
Paper feed motor adjustment.]
1 - 8
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canon iP4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canon iP4000 in the language / languages: English as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info