804892
14
Zoom out
Zoom in
Previous page
1/20
Next page
26
Topstone Neo Carbon OMS
27
Technical Information
Seat Tube / Seat Stay Pivot Bearings
Technical Information
Seat Tube / Seat Stay Pivot Bearings
138222 Rev 1 (03/20)
3
SS SS
NGLI-2
2
1
2
3
5
1
4
7
SS
6
M6 x 70 mm
ST
ST
M6 x 30 mm
Seat Tube / Seat Stay Pivot Bearings
1. Bearing
2. Install Plate
3. Tool Handle
4. Remove Plate
5. Remove Cup
6. Screw M6  70mm
7. Screw M6  30 mm
ST Seat Tube
SS Seat Stay End
REMOVE
1. Remove LockR pivot hardware.
2. Insert remove plate (4) through ST pivot
so its small OD cylindrical surface engages
the inside of the bearing.
3. Insert M5X30mm screw (7) through hole
in remove plate (4) so threads are pointing
out through SS pivot end.
4. Thread tool handle (3) onto M6X30mm
screw (7) only 23 turns.
5. Pull SS end away from ST just enough to
allow remove cup (5) to be snapped over
M6X30mm screw (7).
6. Hold M6X30mm screw (7) stationary with
5mm hex key while turning tool handle (3)
until bearing is fully pulled out of pivot and
into remove cup.
7. Unthread tool handle to remove tool from
the frame.
8. Repeat for the other side.
INSTALL
1. Pull drive side SS end away from ST just
enough to slip larger OD side of install plate
(2) into ST pivot bore.
2. Place new bearing on smaller OD side of
2nd install plate (2).
3. Apply grease to non-drive side ST pivot
bore.
4. Pull non-drive side SS end away from ST
just enough to slip 2nd install plate (2) and
bearing into position.
5. Insert M6X70mm screw (6) through both
install plates so it’s threaded end protrudes
through SS end on non-drive side.
6. Thread tool handle (3) onto M6X70mm
screw (6) and tighten while holding screw
stationary with 5mm hex key. Tighten until
bearing is fully pressed into ST pivot bore.
7. Remove Tool handle (3), M6X70 screw (6)
and drive side install plate (2).
8. Place new bearing on smaller OD side of
install plate (2).
9. Apply grease to drive side ST pivot bore
10. Pull drive side SS end away from ST just
enough to slip install plate (2) and bearing
into position.
11. Insert M6X70mm screw (6) through both
install plates so it’s threaded end protrudes
through SS end on drive side.
12. Thread tool handle (3) onto M6X70mm
screw (6) and tighten while holding screw
stationary with 5mm hex key. Tighten until
bearing is fully pressed into ST pivot bore.
13. Unthread tool handle (3) and remove all
tools from pivot.
14. Continue with LockR axle installation
procedure.
REMOVE
REMOVE
Identification
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cannondale Topstone Neo Carbon 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale Topstone Neo Carbon 2020 in the language / languages: English as an attachment in your email.

The manual is 9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cannondale Topstone Neo Carbon 2020

Cannondale Topstone Neo Carbon 2020 Additional guide - English - 24 pages

Cannondale Topstone Neo Carbon 2020 User Manual - English - 220 pages

Cannondale Topstone Neo Carbon 2020 Additional guide - German - 24 pages

Cannondale Topstone Neo Carbon 2020 User Manual - German - 102 pages

Cannondale Topstone Neo Carbon 2020 Additional guide - German - 38 pages

Cannondale Topstone Neo Carbon 2020 Additional guide - Dutch - 24 pages

Cannondale Topstone Neo Carbon 2020 User Manual - Dutch - 102 pages

Cannondale Topstone Neo Carbon 2020 Additional guide - Dutch - 38 pages

Cannondale Topstone Neo Carbon 2020 Additional guide - French - 24 pages

Cannondale Topstone Neo Carbon 2020 User Manual - French - 102 pages

Cannondale Topstone Neo Carbon 2020 Additional guide - French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info