804898
173
Zoom out
Zoom in
Previous page
1/220
Next page
173
PART 3
STEP 6. Installing the Handlebar And Stem
Assembling Your Bike
Cannondale Bicycle Owner’s Manual
Remove the cardboard tube from the steering tube of the fork. You can discard, recycle, it is just
a spacer for packaging.
There will be one or more round metal spacers on the steering tube. Leave them in place.
Now take the complete stem and handlebar assembly and slide the stem over the steering tube.
Be sure that the handlebar assembly is properly oriented. A good way to check this is to be sure
that:
The shifters are facing up, towards you.
The brake lever on the right controls the rear brake. The rear brake is already connected to
the right hand brake lever, so you can squeeze the lever and see that you have the right hand
brake lever on the correct side of the bike.
The left hand brake lever will be connected to the front brake, but is not at this point.
Once you are sure that the orientation is correct, place the top cap and bolt on top of the stem.
Thread the bolt into the threaded fitting inside the steering tube. Snug this bolt with the 5 mm
allen wrench. Rock the bike forward and back a bit and snug this bolt to eliminate play. You are
setting the bearing pre-load on the headset, the bearings on which the fork pivots. You want to
tighten enough to eliminate noticeable play but want the fork to turn freely without a lot of
resistance. No torque spec here, it’s a matter of feel. Not super tight, but more than finger tight.
Now move the handlebar and stem assembly so that the stem faces directly forward. You can
sight where the front wheel will be in the fork. Once centered, use a 5mm allen wrench to tighten
the two stem clamp bolts to the spec marked on the stem or 7 Nm. You are now clamping the
handlebar and stem assembly to the steering tube and fork so that you can control the bike.
After the wheel is installed and you are doing a final pre-ride check, if you find that the handlebar
and stem assembly is not quite centered, you can loosen the two stem clamp bolts, center the
assembly and then torque the stem clamp bolts to the spec marked on the stem or 7 Nm.
173


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cannondale Moterra Neo 2021 - Shimano E7000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale Moterra Neo 2021 - Shimano E7000 in the language / languages: English as an attachment in your email.

The manual is 12.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cannondale Moterra Neo 2021 - Shimano E7000

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - English - 24 pages

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - English - 30 pages

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - German - 24 pages

Cannondale Moterra Neo 2021 - Shimano E7000 User Manual - German - 102 pages

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - German - 30 pages

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - Dutch - 24 pages

Cannondale Moterra Neo 2021 - Shimano E7000 User Manual - Dutch - 102 pages

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - French - 24 pages

Cannondale Moterra Neo 2021 - Shimano E7000 User Manual - French - 102 pages

Cannondale Moterra Neo 2021 - Shimano E7000 Additional guide - French - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info