Manual Cannondale IQ400 - 2012 (page 2 of 6) (English)

637189

Zoom out

Zoom in

1/6

2012 IQ400 Computer

Setup and Owners Manual - 11/11

2. Pass the two cable ties through the sensor mounting holes and loosely mount the

sensor body to the non-drive side chainstay (do not fully tighten the cable ties at this

point). Install the sensor stabilizing pad between the chainstay and sensor.

3. Secure the sensor to the non-drive side chainstay with 2 nylon ties. Loosely install the

sensor magnet to one of the spokes of the rear wheel. Make sure the silver side of the

magnet faces toward the sensor arm.

Adjust the position of the magnet, sensor arm and sensor together so that the magnet

passes by the full length of the sensor arm and 1-2 mm separates the magnet and

sensor arm.

4. Loosely mount the Cadence Magnet to the inside of the crank arm using 1 of the nylon

ties. Make sure the word “Sensor” faces toward the Cadence Sensor pin and a small

piece of stabilizing pad is installed between the Cadence Magnet and the crank arm.

IMPORTANT: Proper adjustment of the clearances between magnets and sensors must

be accurate for proper computer function. There are multiple ways to make accurate

adjustments and requires care when setting up the sensors.

5. Set the Speed Sensor-to-magnet and Cadence Sensor-to-magnet gaps by tilting the

sensor toward or away from pickup zone. Adjust the position of the Cadence Sensor

pin and Speed Sensor arm as needed - make sure to loosen or tighten the screw on the

front edge of the sensor body when adjusting the Cadence Sensor pin. The maximum

distance between the speed sensor and magnet on the spoke is 5 mm. The maximum

distance between the cadence sensor and magnet on the crank arm is 5mm.

6. When set, draw the nylon ties tight but do NOT fully tighten. This will allow for minor

adjustments after the computer setup is complete.

SETTING THE CLOCK CLK

1. Press FUNCTION until the “CLK” function shows.

2. Press and hold SET for >3 seconds to begin programming.

3. Press SET to change to “12H” or “24H” hour mode.

4. Press the FUNCTION to move the cursor to the hour eld

5. Press SET hour.

6. Repeat steps 4 and 5 to set Minutes and Seconds.

7. Press and hold the FUNCTION button for 3 seconds to exit programming.

GENERAL NOTES FOR PROGRAMMING ALL FUNCTIONS:

• Press and hold SET for 3 seconds to begin programming a function.

• Press the SET to change the value of a selected eld. Press/hold SET to change

value rapidly.

• Press the FUNCTION button to move the cursor to the next eld.

• Press and hold the FUNCTION button for 3 seconds to exit programming.

To begin using the computer, simply press the FUNCTION button. Following installation,

the computer is activated automatically by a rotating wheel.

There are 2 power saving modes - 50% savings if no movement after 5 minutes, 100%

power savings after 30 minutes.

Press the SET button to exit the power saving modes prior to using the computer.

Press the FUNCTION button, to switch the computer through the following functions:

“CLK” – Clock feature, in 12/24 hr format

“TM” – Time ridden for 1 ride

“AVS” – Average speed for 1 ride

“MXS” – Maximum speed for 1 ride

“A. CAD” - Average cadence per minute for 1 ride

“M. CAD” - Maximum cadence for 1 ride

“DST” - Distance ridden for 1 ride

“ODO” – Total miles ridden for all rides

“KCAL” – Calories burned (estimate) for 1 ride

“DAILY” – Distance ridden in the past 24 hours

“

SCAN

”

– Computer display scans all functions. Press the FUNCTION button to stop

scanning.

To turn on the backlight, press and release the SET button. The backlight will stay

on for three (3) seconds.

“TM, AVS, MXS, DST, and KCAL“ are recorded automatically as soon as the wheel moves.

A CAD and M CAD are automatically recorded as soon as the crank moves. Recording stops

if the wheel stops. Cadence recording stops if the crank stops. To clear this information,

press and hold the SET button in the “TM” mode.

MAIN DISPLAY AND FUNCTIONS

CURRENT SPEED

SPEED SCALE

SUB-DISPLAY

MODE

SET Button

(back of unit)

FUNCTION Button

FUNCTIONS DISPLAY

CADENCE

MOTION SIGNAL

**This button also,

activates the display

backlighting.

SETTING CALORIES BURNED KCAL

This computer can estimate calories burned while riding. The estimate is based on weight,

gender, time ridden and average speed. IMPORTANT: The estimate is truly an estimate.

Actual calories burned will vary depending on many variables the computer does not

calculate such as heart rate.

1. Press FUNCTION until the “KCAL” displays.

2 Press and hold SET for >3 seconds to begin programming.

3. Press SET to select gender “MALE” or “FEMALE”.

4. Press FUNCTION to store gender.

5. Press SET to change weight unit “Kg” or “Lb”.

6. Press FUNCTION to begin entering your weight in unit selected.

7. Press or hold Set to change the weight. Range: 0 ~ 150 Kg, 0-330 Lb.

8. Press and hold the Function for 3 seconds to exit programming.

RESETTING THE ODOMETER ODO

If the battery is replaced, it is possible to update the odometer to the mileage on your bike

after replacing the battery.

1. Press FUNCTION until the “ODO” displays.

2. Press and hold SET for >3 seconds to begin programming.

3. Press FUNCTION until “00000” (ve zeros) and “ODO” appears on the screen

4. Press SET to change the appropriate numbers. Press FUNCTION to change cursor

position.

5. Repeat step 4 until the odometer is set.

6. Press and hold FUNCTION for 3 seconds to exit programming.

7. Verify the computer shows speed and cadence. If not, you may have to complete the

Final Set Up steps shown in these instructions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale IQ400 - 2012 in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cannondale IQ400 - 2012 Manual

Product: