804908
18
Zoom out
Zoom in
Previous page
1/25
Next page
E-Series Owner’s Manual Supplement - 130374
ESPAÑOL ITALIANO NEDERLANDS FRANÇAIS DEUTSCH ENGLISH
17
Charging Procedure
The charging procedure begins as soon as the charger is connected
to the battery or the charge socket on the bike and the mains.
Note: The charging procedure is only possible when the temperature
of the battery pack is within the allowable charging temperature
range.
Note: The drive unit is deactivated during the charging procedure.
The battery can be charged with and without the HMI. When
charging without the HMI, the charging procedure can only be
observed on the battery charge-control indicator. When the HMI
is connected, the back lighting of the display is switched on at low
luminosity and “Charging appears in the text display.
The HMI can be removed during the charging procedure, or it can
also be fitted after the charging procedure has begun.
The charging state is displayed by the battery charge-control
indicator A3 on the battery and by the bars on the HMI.
When charging the main battery on the bike, the battery of the HMI
can also be charged.
During the charging procedure, the LEDs of charge-control indicator
A3 on the battery pack light up. Each continuously lit LED is
equivalent to a charge capacity of approx. 20%. The flashing LED
indicates the charging of the next 20%.
■ Use caution when touching the charger during the charging
procedure. Wear protective gloves. Especially in high ambient
temperatures, the charger can heat up considerably.
Once the battery is fully charged, the LEDs extinguish immediately
and the HMI is switched off. The charging procedure is terminated.
The charging state can be displayed for 3 seconds by pressing the
on/off button A4.
Disconnect the charger from the mains supply and the battery pack
from the charger.
When disconnecting the battery pack from the charger, the battery
pack is automatically switched off.
Note: If you have charged the battery on the bike, carefully close
the charge socket C6 with the cover C7 after the charging procedure
so that no dirt or water can get in.
If the charger is not disconnected from the battery after charging,
after a few hours the charger will switch itself back on, check the
charging state of the battery and begin the charging procedure
again if necessary.
Troubleshooting –
Causes and Corrective Measures
Cause Corrective Measure
Two LEDs of the battery pack
flashing.
Battery pack defective Refer to an authorised
bicycle dealer
Three LEDs of the battery
pack flashing.
Battery pack too warm or too
cold
Disconnect the battery
from the charger until the
charging temperature range
has been reached.Do not
connect the battery pack
to the charger until it has
reached the allowable charging
temperature.
No charging procedure possible (no indication on battery pack)
Plug not inserted correctly Check all plug connections
Contacts of battery pack soiled Carefully clean the contacts of
the battery pack
Socket outlet, cable or charger
defective
Check mains voltage, have
charger checked through
bicycle dealer
Battery pack defective Refer to an authorised bicycle
dealer
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cannondale E-series 2014 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale E-series 2014 in the language / languages: English as an attachment in your email.

The manual is 8.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cannondale E-series 2014

Cannondale E-series 2014 Additional guide - German - 25 pages

Cannondale E-series 2014 Additional guide - Dutch - 25 pages

Cannondale E-series 2014 Additional guide - French - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info