624611
26
Zoom out
Zoom in
Previous page
1/106
Next page
24 25
PART I
(continued from previous page...)
(2) With the steering fork facing forward, insert the
wheel between the fork blades so that the axle
seats firmly at the top of the fork dropouts. The
cam lever, if there is one, should be on rider’s left
side of the bicycle (fig. 8a & b). If your bike has a
clip-on type secondary retention device, engage
it.
(3) If you have a traditional cam action mechanism:
holding the cam lever in the ADJUST position
with your right hand, tighten the tension
adjusting nut with your left hand until it is finger
tight against the fork dropout (fig. 8a). If you
have a cam-and-cup system: the nut and cup
(fig. 8b) will have snapped into the recessed area
of the fork dropouts and no adjustment should
be required.
(4) While pushing the wheel firmly to the top of the
slots in the fork dropouts, and at the same time
centering the wheel rim in the fork:
(a) With a cam action system, move the cam lever
upwards and swing it into the CLOSED position
(fig. 8a & b). The lever should now be parallel
to the fork blade and curved toward the wheel.
To apply enough clamping force, you should
have to wrap your fingers around the fork blade
for leverage, and the lever should leave a clear
imprint in the palm of your hand.
(b) With a through-bolt or bolt-on system, tighten
the fasteners to the torque specifications
in Appendix D or the hub manufacturer’s
instructions.
NOTE:
If, on a traditional cam action system, the lever
cannot be pushed all the way to a position
parallel to the fork blade, return the lever to the
OPEN position. Then turn the tension adjusting
nut counterclockwise one-quarter turn and try
tightening the lever again.
(6) With a through-bolt or bolt-on system, tighten
the fasteners to the torque specifications
in “PART II Tightening Torques or the hub
manufacturer’s instructions.
WARNING
SECURELY CLAMPING THE WHEEL WITH
A CAM ACTION RETENTION DEVICE TAKES
CONSIDERABLE FORCE.
If you can fully close the cam lever without
wrapping your fingers around the fork blade for
leverage, the lever does not leave a clear imprint
in the palm of your hand, and the serrations on
the wheel fastener do not emboss the surfaces
of the dropouts, the tension is insucient.
Open the lever; turn the tension adjusting nut
clockwise a quarter turn; then try again.
See also WARNING on page 20.
(6) If you disengaged the brake quick-release
mechanism in 3. a. (1) above, re-engage it to
restore correct brake pad-to-rim clearance.
(7) Spin the wheel to make sure that it is centered
in the frame and clears the brake pads; then
squeeze the brake lever and make sure that the
brakes are operating correctly.
c. Removing a disk brake or rim brake rear
wheel
(1) If you have a multi-speed bike with a derailleur
gear system: shift the rear derailleur to high gear
(the smallest, outermost rear sprocket).
If you have an internal gear rear hub, consult your
dealer or the hub manufacturer’s instructions
before attempting to remove the rear wheel.
If you have a single-speed bike with rim or disk
brake, go to step (4) below.
(2) If your bike has rim brakes, disengage the
brake’s quick-release mechanism to increase the
clearance between the wheel rim and the brake
pads (see Section 4.C, figs. 11 through 15).
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cannondale 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cannondale 2016 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info