495645
8
Zoom out
Zoom in
Previous page
1/24
Next page
ENG
5
1.Place the hob into the opening on worktop. The size of opening
is given in Figure 11.
Fordetails, see the headings either Fixing the solid hotplate hob
or Fixing the vitroceramic hob.
.2.Connect the hob to the oven using the the plug given on the
hob. The socket for plug is placed on the rear panel of oven.
3.Connect the oven to the electrical supply.
4.Place the oven into its built-in niche. Either placement in Figure
11 is applicable depending on the size of cabinet opening. For
details, see the heading Fixing the oven.
5.2.1. Installation Steps
5.2.2. Fixing the solid hotplate hob
In order to prevent leakage of any liquids on the counter, a special
sealing putty is supplied together with your oven. Apply this putty
around the clearance on the kitchen counter. Extend the five-
piece putty by stretching and apply it around the clearance. Place
the hob on it, as indicated in the Figure 11. Make sure to fit all four
clamps by using one screw for each as shown in the Figure 12. In
case the thickness of the kitchen counter is less than 40mm, use
the clamp as shown in the Figure 14. After fitting your hob into its
place, neatly remove the excess sealing putty around the sides
with the help of a spatula Figure 13.
5.2.3. Fixing the vitroceramic hob
Apply the one-sided self-adhesive sealing tape supplied
all the way round the lower edge of the cooking surface along the
outer edge of the glass ceramic panel. Do not stretch it.
Screw the 4 worktop mounting brackets on the side walls
of product.
Place the hob into the opening on the worktop.
Figure 13
h>40mm
h
h<40mm
h
Figure 12
Figure 14
Worktop mounting braket
5.2.4. Fixing the oven
Fit the oven into the space provided in the kitchen unit; it may be
fitted underneath a work top or into an upright cupboard. Fix the
oven in position by screwing into place, using the two fixing holes
in the frame. To locate the fixing holes, open the oven door and
look inside.
To allow adequate ventilation, the measurements and distances
indicated in the diagram on last page must be adhered to when
fixing the oven.
The dimensions and material of the cabinet in which the oven will
be installed must be correct and resistant to increases in
temparature. In a correct installation, contact with electrical or
insulated parts must be prevented. Insulating parts need to be
fitted in a way to ensure that they cannot be removed by using any
kind of tool. Installing the appliance in the close vicinity of a
refrigerator or a deep-freezer is not recommended. Otherwise, the
performance of the above-mentioned appliances will be
negatively affected due to emanating heat.
5.2.5. Warning
Warning regarding the installation of built-in oven without cooling
fan.
Prior inserting the oven, it is necessary to remove the rear kitchen
element panel in the area of the oven opening.
Equally, the front part of the element must have an opening.
Figure 15
Figure 16
2
60 cm
2
240 cm
2
120 cm
2
180 cm
08 GB
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Candy FCO 105W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Candy FCO 105W in the language / languages: English, German as an attachment in your email.

The manual is 5,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info