46495
9
Zoom out
Zoom in
Previous page
1/37
Next page
AUTOMATIC FAULT SIGNALS
17
Turn off the dishwasher, open the
inlet hose and reset the cycle.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
Check if the drain tube is bent or if
the siphon or filters are clogged.
If the problem persists, contact
Customer Service.
Contact Customer Service.
Contact Customer Service.
Clean the filter plate.
If the problem persists, contact
Customer Service.
FAULTS CAUSE SOLUTION
E2 appears on the display and
the buzzer sounds.
E3 appears on the display and
the buzzer sounds.
E4 appears on the display and
the buzzer sounds.
E5 appears on the display and
the buzzer sounds.
E6 appears on the display and
the buzzer sounds.
E8 or Ei appear on the display
and the buzzer sounds.
No water (inlet hose closed).
The machine cannot drain water.
Water leak
Electronic temperature control fault.
Electronic control fault.
The water heating element is not
working correctly or the filter plate is
clogged.
The dishwasher is able to signal a series of faults in the display.
16
"DELAY START" button
Dishwasher start time can be set with this
button, delaying start from 1 to 23 hours.
Proceed as follows to set a delayed start:
Press the "DELAY START" button ("00"
will appear on the display).
Press the button again to increase the
delay in hours (each time the button is
pressed the delay is increased by 1 hour
to a maximum of 23).
To start the countdown press the "START"
button. At the end of the countdown, the
program will automatically start.
If you wish to see which programme has
been selected, press the "PROGRAMME
SELECTION" button.
Proceed as follows to cancel a delayed
start:
Hold the "START" button down for at
least 5 seconds.
At this point, a new program and option
buttons must be set to start a new
program as indicated in the "PROGRAM
SETTINGS" section.
Buzzer mute
The buzzer may be muted as follows:
With the dishwasher off, hold down the
"PROGRAMME SELECTION" button
for few seconds while simultaneously
pushing the "ON/OFF" button.
"b1” will appear on the display to indicate
that the buzzer is on.
Press the "PROGRAMME SELECTION"
button again "b0" will appear on the
display to indicate that the buzzer is off).
Wait for a buzzer to sound to indicate
that the settings were saved.
To turn the buzzer on again, follow the
same procedure ("b1" will appear on the
display to indicate that the buzzer is on).
WARNING!
To ensure the correct operation of
the anti-overflow safety device, it is
recommended not to move or to tilt
the dishwasher during operation.
If it is necessary to move or to tilt the
dishwasher, first make sure the
washing cycle is finished and that no
water is left in the tank.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Candy CDI 4015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Candy CDI 4015 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish, Spanish as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info