764874
18
Zoom out
Zoom in
Previous page
1/32
Next page
Owners Manual
PRIMING MODE
This mode will last for 4-5 minutes or you can manually exit the priming mode after the pump(s) have primed.
Regardless of whether the priming mode ends automatically or you manually exit the priming mode, the system will automatically return to
normal heating and filtering at the end of the priming mode. During the priming mode, the heater is disbaled to allow the priming process to
be completed without the possibility of energizing the heater under low-flow or no-flow conditions. Nothing comes on automatically, but the
pump(s) can be energized by pushing the “Jet” buttons.
EXITING PRIMING MODE
You can manually exit Priming Mode by pressing a “Temp” button (Up or Down). Note that if you do not manually exit the priming mode as
described above, the priming mode will be automatically terminated after 4-5 minutes. Be sure that the pump(s) have been primed by this
time.Once the system has exited Priming Mode, the top-side panel will momentarily display the set temperature but the display will not show
the temperature yet, as shown below. This is because the system requires approximately 1 minute of water flowing through the heater to
determine the water temperature and display it.
MODE - READY AND REST
READY Mode will circulate water every 1/2 hour, using Pump 1 Low, in order to maintain a constant water temperature, heat as needed, and
refresh the temperature display. This is known as “polling.” REST Mode will only allow heating during programmed fi lter cycles. Since polling
does not occur, the temperature display may not show a current temperature until the heater pump has been running for a minute or two.
Configuration: Your Control Centre
OPERATIONS
PRIMING PUMPS
As soon as the above display appears on the panel, push the “Jet” button once to start Pump 1 in low-speed and then again to switch to
high-speed. Also, push the Pump 2 if you have a 2nd pump, to turn it on. The pumps will now be running in high-speed to facilitate priming. If
the pumps have not primed after 2 minutes, and water is not flowing from the jets in the spa, do not allow the pumps to continue to run. Turn
off the pumps and repeat the process.
Note: Turning the power off and back on again will initiate a new pump priming session. Sometimes momentarily turning
the pump off and on will help it to prime. Do not do this more than 5 times. If the pump(s) will not prime, shut off the
power to the spa and call for service.
18
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canadian Spa Company Toronto at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canadian Spa Company Toronto in the language / languages: English as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Canadian Spa Company Toronto

Canadian Spa Company Toronto User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info