Manual Canadian Spa Company Halifax 2016 (page 21 of 32) (English)

764908

Zoom out

Zoom in

1/32

Owners Manual

Spa operation - ML551Control Pad (UK/Europe/North America)

START UP

When your spa is ﬁrst powered up, it will go into Priming mode, indicat-

ed by “Pr.” The Priming mode will last for less than 5 minutes (press

“Warm” button to skip Priming Mode) and then the spa will begin to heat

and maintain the water temperature in the Standard mode.

TEMPERATURE ADJUSTMENT

Temp (80°F - 104°F / 26°C - 40°C)

The start-up temperature is set at 100F°/37°C. The last measured

temperature is constantly displayed on the LCD.

Note: that the last measured spa temperature displayed is current

only when the pump has been running for at least 2 minutes.

Press the “Warm2” or “Cool” button to display and adjust the set

temperature. After 3 seconds, the LCD will automatically display the last

measured spa temperature.

JETS 1

Touch the “Jets 1” button once to activate the low speed of the pump and

again for the high speed. Press the “Jets 1” button again to turn off the

pump. If left running, the low speed of the pump will automatically turn off

after 4 hours, and the high speed will automatically turn off after 15

minutes. It may also activate for at least 2 minutes every 30 minutes

to detect the spa temperature and then to heat to the set temperature

if needed, depending upon mode. When the low speed turns on auto-

matically in its Filtration cycle, it cannot be deactivated from the panel;

however, the high speed may be started.

Note: Filtration Cycles will activate every 12 hours from the time spa was

ﬁrst powered up.

Note: Circulation pumps may also be installed into some makes of spas,

which will run the heater and ﬁltration cycles. The circulation pump cannot

be controlled on the topside panel and will run for duration of heating or

Filtration cycles.

JETS 2

Touch the “Jets 2” button once to activate and again to turn off. If left

running the Pump will automatically turn off after 15 minutes.

Note: Jets 2 will purge for 5 minutes at the beginning of each ﬁlter cycle.

JETS 3

Touch the “Jets 3” button once to activate pump 3, and press again to

turn off. If left running jets 3 will automatically turn off after 15 minutes.

Note: Jets 3 will purge for 5 minutes at the beginning of each ﬁlter cycle.

BLOWER/JETS 4

Touch the “Blower/Jets 4” button once to activate pump 3, and press

again to turn off. If left running Blower/Jets 3 will automatically turn off

after 15 minutes.

Note: Jets 4 will purge for 5 minutes at the beginning of each ﬁlter cycle.

LIGHT

Press the “Light” button to turn the light on and off. If left on, the light

automatically turns off after 4 hours.

To change the light effect sequence: Press the light button on then

off, then immediately press the button again (within 5 seconds) to

allow you to select another lighting effect (i.e ﬂashing, intermittent,

fading) repeat sequence until desired lighting effect is achieved.

MODE

This button is used to switch between Standard, Economy or Sleep Mode

settings.

• Standard Mode (“Std”) is programmed to maintain the desired

temperature. Note that the last measured spa temperature displayed is

current only when the pump has been running for at least 2 minutes.

“Std” will be displayed momentarily when you switch into Standard

Mode. (Spa will restart heating when 0.5 degree temperature is lost in

spa)

• Economy Mode (“Ecn”) heats the spa to the set temperature only

during ﬁlter cycles. “Ecn” will alternate with temperature when

heater current, “Ecn” will display solid when heater is not current. (Spa

will only heat within Filter cycle sessions)

• Sleep Mode (“SLP”)heats the spa to within 20°F/10°C of the set

temperature only during ﬁlter cycles.

“SLP” will alternate with temperature when heater current, “SLP” will

display solid when heater is not current. (Spa will only heat within Filter

cycle sessions)

To switch between Modes. Press “Mode” button, then “Cool” button until

you reach desired mode, then press “Mode” button to select.

PRESET FILTER CYCLES

The ﬁrst Filter Cycle begins 6 minutes after the spa is powered up. The

second Filter Cycle begins 12 hours later.

Filter duration is programmable from 1 to 12 hours. Indicated by ‘F 1’, ‘F

2’, ‘F 3’ until ‘F 12’

- The default Filter time is ‘F 2.’

- To program, press “Warm” button, then “Jet 1.”

- Press the “Cool” button to adjust to desired setting.

- To select and continue press “Jet 1” button. “DN”, “D” or “N” will

now be shown on display.

• “DN” = Day and Night Filtration

• “D” = Day Filtration

• “N” = Night Filtration

(Please note: 2 Filtration cycles daily is recommended)

- To Select Program press “Cool” until desired setting.

- To select and Exit press “Jet 1” button

Freeze Protection - ICE

If the temperature sensors detect a drop to approximately 44 °F (6.7 °C)

within the heater, then the pump(s) and blower will automatically activate

to provide freeze protection.

The equipment will stay on until 4 minutes after the sensors detect that

the spa temperature has risen to approx. 45°F (7.2 °C) or higher.

N.B. In colder climates, an optional additional freeze sensor may be added

to protect against freeze conditions that may not be sensed by the

standard sensors. Aux freeze sensor protection acts similarly except

with the temperature thresholds determined by the switch and without a

4-minute delay in turn off. See your dealer for details.

ML551 (8 Button) GL2KM3 St Lawrence 13 & 16’ Swim Spa (UK/Europe)

ML551 (8 Button) EL2000 St Lawrence 13 & 16’ Swim Spa (North America)

Molex type

ML/GL Connector

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Canadian Spa Company Halifax 2016 in the language / languages: English as an attachment in your email.

The manual is 3,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Canadian Spa Company Halifax 2016 Manual

Product: