764908

Canadian Spa Company Halifax 2016 Manual

14
Zoom out
Zoom in
Previous page
1/32
Next page
Owners Manual
13
Starting your hot tub/spa
FILLING UP YOUR HOT TUB/ SPA
IMPORTANT: Before filling the spa, it is important to read and
understand the water chemistry section of this manual. Do not
proceed until the water chemistry section is understood and the source
water is tested.
Verify that the spa is in the desired final location. Refer to the
‘Choosing a Location’ section - once filled, the spa cannot be moved
without draining.
Follow these filling instructions to avoid damage to the spa pumps:
1. Leave power to the spa off until spa is completely filled.
2. Never leave an unfilled spa exposed to direct sunlight without the
Spa Cover installed. Resulting damage such as bubbles and
wrinkles in the spa shell and fading of the jet faces is not
covered by the manufacturer’s warranty.
3. Never operate spa pumps without water because this could result
in permanent pump and/or heater damage which is not covered
by the manufacturer’s warranty.
4. Remove all warning labels from spa shell.
5. Apply Acrylic Surface Protection solution if desired to keep the
spa shell clean, especially around the water line. Follow package
instructions.
6. Remove the filter lid, basket and filter cartridge.
7. Inspect all Jets (shipping may cause jets to become loose or
detached). Check to see that the Black Drain Valve (located to
the left or right of the front access panel) is closed and that all
barrel unions are tight. The slice valves should be open.(valve is
open when the handle is pulled up, closed when it is pushed in).
IMPORTANT: Follow the next steps closely to prevent damage to
the Spa Pumps.
8. Insert garden hose or other clean water source directly into filter
housing. Push hose pipe into filter housing until it stops. Fill up to
bottom of spa pillows. Secure hose placement and turn on water.
The spa can be filled with tepid water. If warm water is used, the
spa will be available for use in a shorter period of time.
9. Filling spa through the filter housing prevents air lock in the spa
pumps, which is an air pocket preventing the flow of water
through the pump. Permanent damage caused by running the
pump with an air lock (or without water) is not covered by the
manufacturer’s warranty.
10. Check for leaks! Although spas are fully checked at the factory,
shipping and delivery might cause a leak.
11. Before power is applied familiarise yourself with the spa
control operations.
12. Adding a Scale Control during the filling process to reduces
limescale. Follow package instructions.
13. Fill the spa until water is 1 inch (25mm) above the waterline on
the spa shell or 1 inch (25mm) above the mid point of the
filter housing. Do not overfill the spa. If needed, more water may
be added after the power is turned on and the plumbing is
filled. See Powering Up Spa section.
14. Turn water off and remove hose.
15. Reinstall filter cartridge, basket and filter lid.
16. Add Start-up Chemicals after power is turned on. Refer to
Powering Up the Spa section.
DRAINING YOUR HOT TUB/ SPA USING THE DRAIN VALVE
1. Start by shutting off the electrical breaker connected to your spa
2. Open the drain valve located at the side of the spa and let the
water drain out. This valve has a straightforward locking
mechanism that stops the water from flowing out while you
attach a garden hose to the cap. Here are the steps to
operate your valve:
3. With the valve extended, unscrew the cap from the middle of the
valve.
4. Screw in the male end of the garden hose to the valve and run
the hose to your drain location. When ready, push the valve back
in and twist it to empty the water from the spa.
5. Once the water has stopped flowing out of the drain valve, use
the wet/dry vacuum to suck out any remaining water from each
jet head (NOTE: If your spa is equipped with a blower, briefly turn
the power to the spa back on and run the blower for 10 seconds
to remove excess water. Shut off the power when finished).
6. Twist valve and pull out to CLOSE.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Canadian Spa Company Halifax 2016 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Canadian Spa Company Halifax 2016 in the language / languages: English as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info