801630
6
Zoom out
Zoom in
Previous page
1/106
Next page
6
11. Do not use accessories that are not recommended by the manufacturer. They can be
dangerous to the user and may damage the device.
BEFORE FIRST USE
Check that all connections are completely secure and that the device is securely positioned before using it. The device must be placed
at a distance of at least 1 meters from the nearest wall. The box with the switch must be at least 30 cm from a ceiling and 1.80 meters
above the ground. The device must be placed firmly on an even and completely horizontal surface.
ASSEMBLING
1. Place the lower part of the stand (7) on the round base (6) so that the screw holes align. From the bottom of the base, screw in the
large knob with a metal washer (11).
2. Slide the central part of the stand (8) over the lower part (7). Insert the 4 screws through the double holes and tighten them firmly.
3. Then attach the upper part of the stand (9) to the central part (8). To do this, first insert the thinner adjustable part of the stand (10) into
the upper part of the stand (9). Insert the 4 screws through the double holes and tighten them firmly.
4. Pull out the thinner adjustable part of the stand (10) as far as you want and tighten the fixing knob (5).
5. Put the head housing (1) on the top of the stand (10) and tighten the head with the screw (13) on the back of the head.
6. The head has a vertically adjustable tilt angle in 3 positions, press the head down or up to choose the best angle of heat.
7. The thin part of the stand (10) can rotate 360 °, allowing the head (1) of the device to be directed in any direction. The electric cable
can be attached to the cable holders on the stand.
Device description – picture 1
1. Head housing 2. Grid 3. ON / OFF switch
4. Stand 5. Fixing knob 6. Round base
7. Stand, lower part 8. Stand, central part 9. Stand, upper part
10. Stand, thinner adjustable part 11. Large knob with a metal washer
12. 8 short screws for mounting the stand 13. Screw for securing the head
PATIO HEATER OPERATION
1. Point the head of the device in the correct direction.
2. Insert the plug into the socket (220-240V / 50Hz).
3. The device is switched on and off by the ON/OFF switch (3).
You also select the heating power output with the switch:
0 = 0 Watt
Left: = low power 1000W
Left + Right = high power 2000W
4. The device does not have a thermostat and continues to give out heat until it is switched off. Always keep a close eye on the device
when it is switched on!
5. Remove the plug from the socket when the device is not in use.
Heating element replacement - see page 3
1. Set the power switches to position 0. Disconnect the device from power.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Camry CR 7737 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Camry CR 7737 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 4.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info