734430
6
Zoom out
Zoom in
Previous page
1/68
Next page
6
21. Never use the fan heater in high humidity rooms – bathroom, shower room, swimming
not used, the power plug has to be removed from the power outlet.
24. Flammable materials, for example furniture, bedclothes, paper, clothes, curtains should
20. Always turn the fan heater off and set the thermostat dial to minimum before removin
temperature controlling device or time switch.
pools etc. The humidity can cause short circuit, and effect in damaging the device.
be kept at least one meter from the fan heater.
25. Do not cover the device or put any objects on it while it is operating. Do not use the
22. The operating fan heater needs to be under supervision and in sight all the time. If you
23. Do not connect the fan heater to the automatic switching device, for example
are leaving the room with the fan heater, always turn the fan heater off. If the fan heater is
19. Place the fan heater only on flat, stable surface
the power plug from the socket.
device to dry clothes.
29. Some parts inside the device can be hot or cause sparking. Do not use the fan heater in
be placed near hot surfaces of the fan heater. Do not place the fan heater directly under
A. ON/OFF / Standby Mode button B. Heat button
PRODUCT DESCRIPTION: LED CERAMIC FAN HEATER
C. Oscillation button D. Timer button
1. Once the power switch (5) on the rear of the device has been switched on, use the On/Off switch (A) to power on the device. Once
pressed the other functions will be activated.
2. By pressing the heating button (B) once will activate low heating level, the display will light up icon (F). By pressing a second time will
activate high heating level, the display will light up icon (G). When pressed the heating button (B) a third time heat mode will be
switched off.
the power outlet.
5. By pressing the oscillation button (C) - keep it longer time - to activate left – right direction oscillation, to deactivate press again.
6. After operation, press the On/Off switch (A), the device will cool down automatically and switch off after 30 seconds.
27. The heating surfaces can heat to a temperature of 60 °C or higher. The fan heater
28. The device is not intended to be installed or used in vehicles.
places, where gasoline, paints or other flammable materials are used or stored.
3. Heat outlet 4. Tip-over switch (located on the base)
26. The power cord should not be placed above the fan heater, and it should not touch or
E. Temperature adjustment button F. Low heat 900W icon
should be in a place that children and animals do not have access to.
CONTROL PANEL
G. High heat level 1800W icon I. Desired temperature level icon
1. Control Panel 2. Digital display
5. Power switch 6. Carry handle 7. Power cord
H. Timer activation icon
USSING THE DEVICE
4. By pressing the timer button (D) chose desired time operation from 1 to 8 hours. Display will light up the icon (I). When the time has
elapsed the device will power off.
3. By pressing the temperature adjustment button (E) the desired temperature can by adjusted in range 10-35°C. Desired temperature
level will be shown on the display by icon (H). To decrease temperature press the temperature adjustment (E) button too. When
desired room temperature would be achieved the device will stop heating. The device will blow air with a temperature close to the
content of the ambient temperature.
1. OVER TIP SWITCH Your heater is designed to automatically shut the heater off when tipped forward or backward. The unit will
automatically turn on once it is returned to its normal upright position. Do not use on thick and long pile carpets, as the heater may not
work, due the tip over switch not been activated.
WARNING: During use, do not touch or cover the air inlet and air outlet.
1. Make sure the fan heater is not hot.
CLEANING AND MAINTENANCE
2. OVERHEAT PROTECTION In the event of abnormal overheating, a safety device shuts down the appliance automatically. After a short
cooling down phase, the appliance is ready for use again. If you still notice the same defect as above mentioned, remove the plug
from the socket and consult your authorized dealer to your after-sales service department.
2. Before cleaning the device remove the plug from the electrical socket.
3. Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings.
SAFETY PORTECTION
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Camry CR 7720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Camry CR 7720 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 2,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info