Manual Campingaz IR 5000 THERMO (page 8 of 56) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

662406

Zoom out

Zoom in

1/56

2-a-IR 5000 Turbo Version

Plug in the appliance.

Caution: The appliance was designed to be supplied with

a 230 V 50 Hz voltage. Your installation must be equipped

with a grounding connection compliant with electrical

systems specifications in force.

- Do not place the heater just below an electric socket.

- Do not use the heater near a bath, shower or

swimming pool.

2-b-IR 5000 Version and IR 5000 Turbo Version

Set handle (A) to position (START) and press the

handle for 15 seconds to allow the gas to reach the

pilot burner (fig. 5).

2-c-IR 5000 Thermo Version

Set handle (C) to the maximum position (IIII) and press

control button (A) for 15 seconds to allow the gas to

reach the pilot burner (fig. 5).

3- Fully press several times the LH button marked with a

stylised lightning (

) (B) for lighting up the flame,

while holding handle (A) or control button (A) depressed

for 15 seconds. The thermocouple is activated and the

safety valve does not cut off gas feed.

Release button A or handle A.

4- Check whether the appliance did light up. If not, repeat

the procedure from step 2.

Note: Some air may be trapped in the gas line. This will

prevent the appliance from lighting up during the first

attempt. In this case, it is necessary to repeat the ignition

procedure several times until the safety pilot burner lights

up. During appliance operation, the safety pilot burner

must remain permanently lit in order to ensure correct

operation of the atmosphere analyser.

During the first setting to service, operate the appliance at

maximum power for at least 15 minutes in order to eliminate

the typical new appliance smell due to the presence of

protecting substances applied to the component parts.

Ventilate the room during this operation.

E - 2 - Setting temperature or power (FIG. 5):

Your appliance is equipped with a setting handle which

makes it possible to adjust the temperature radiated by

the infrared panel depending on the temperature desired

in the room.

a) IR 5000 Version and IR 5000 Turbo Version

- Set the heating temperature by positioning handle

index between positions (III) and (I) (3: see fig. 5 - IR

5000 - item A

and - IR 5000 Turbo - reference A)

b) Exclusive to IR 5000 Turbo Version

After lighting up your appliance in compliance with

the indications of paragraph E-1, you can increase its

heating performance by means of the ''Turbo" function.

The "Turbo" function provides for fast and even heating

of the room because it uses a tangential ventilation to

propel the hot air now out of the appliance.

The "Turbo" function is turned on / off by pressing the

red button (fig. 5 - IR 5000 Turbo - item C).

CAUTION:

The appliance was designed to be supplied with a

230 V 50 Hz voltage.

Your installation must be equipped with a grounding

connection compliant with electrical systems

specifications in force.

c) IR 5000 Thermo Version

- Set the heating temperature by positioning handle

index between positions maximum (IIII) and

minimum (I) (see fig. 5 - IR 5000 Thermo - item C)

- Open appliance rear plate (fig. 1 item 3).

Note: If the appliance is new, remove the plastic cable

tie (Figure 1 number 4), lift and remove rear plate (3).

D - 1 - Installing gas bottle:

- Position the gas bottle on the floor behind the appliance.

- Check whether bottle cock and/or pressure reducing

valve handle is in “closed” position.

- Screw in or engage pressure reducing valve to gas

bottle or gas bottle cock (fig. 3 item B).

- Install gas bottle through appliance rear so that the

hose does not touch appliance metal panels and is not

excessively bent or pinched.

- Check that the hose runs normally and is neither bent

nor pulled.

- Install appliance rear plate (fig. 4 item A).

D - 2 - Tightness:

In case of leak, appliance gas supply must be shut

down using gas bottle cock and/or pressure reducing

valve handle.

Do not carry out leak tests with a flame, use a gas leak

detecting liquid.

- Apply gas leak detecting liquid to bottle/pressure

reducing valve/hose/appliance unions.

- Open the gas inlet (bottle cock and/or pressure reducing

valve handle) (fig. 4).

- If bubbles appear, this means that there are gas leaks.

- To remove the leak, tighten hose nuts and/or hose

clamps if any. If a part is defective, have it replaced.

The appliance should not be returned to service until the

leak is removed.

- Close gas bottle cock.

Important: In case of gas leak or odour, immediately

close bottle cock and/or pressure reducing valve

handle. Enhance room ventilation by opening the

windows. Ask a specialised technician to check the

appliance and proper bottle connection.

A leak test should be carried out at least once a year and

whenever the gas bottle is changed.

E - UTILISATION

OPERATING PRECAUTIONS:

DO NOT install the appliance next to a wall, curtains

or a sofa or armchair.

DO NOT cover the appliance with clothes or other

objects.

DO NOT move the appliance when in operation.

The appliance must ALWAYS be directed to the

centre of the room.

The appliance must be put in a dry place.

This appliance protecting grid is designed to

prevent fire hazards or burns and no part shall be

permanently removed.

THE GRID DOES NOT TOTALLY PROTECT YOUNG

CHILDREN OR THE DISABLED.

E - 1 - IGNITING THE APPLIANCE:

Note: Gas opening and closing controls are located on

gas bottle and/or on pressure reducing valve.

The ignition spark, gas inlet control and power control are

operated on the control panel located in the top right-hand

corner of the appliance. (fig. 1 item 1) and (fig. 5 items A,

B and C)

1- Open bottle cock and/or pressure reducing valve

handle and carry out a leak test.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Campingaz IR 5000 THERMO in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Campingaz IR 5000 THERMO Manual

Product: