662235
10
Zoom out
Zoom in
Previous page
1/132
Next page
- that the ventilation openings in the gas receptacle
housing are not obstructed, if appropriate.
- that the grease trap(s) is (are) correctly inserted into its
(their) compartment and that it (they) is (are) correctly
positioned, as far as it (they) will go.
- that the heat reflector is correctly installed in the bottom
of the bowl.

p- cleaning).
h) LIGHTING THE BARBECUE BURNERS
Your barbecue is equipped with a STOPGAZ system. This
safety system automatically shuts off the gas flow to the
burner when the burner flame is blown out (wind etc.).
- Open the lid.
- Make sure that the control knobs are in the "OFF"
position (O).
- Open the gas cylinder valve.
- Press, then turn the knob corresponding to the burner
in a counter-clockwise direction to the (
) position.
Press the ignition button ( ).
- Keep the button depressed for a maximum of 10
seconds. If the burner does not light after 10 seconds,
reset the control button to the OFF (O) position. Wait
for a minute before starting the ignition procedure once
more.
- When the burner is lit, keep the control button depressed
for 10 seconds and then release it. This enables the
STOPGAZ safety system to activate.
- Adjust the flame to the desired height by turning the
knob to (
) or ( ).
- Do the same for all the burners.
- If the electronic ignition system does not work, light the
barbecue manually (next paragraph).
Lighting the burner manually
- If the electronic ignition system fails to work, use a match
to light the burner.
- Open the lid.
- Make sure that the control knobs are in the "OFF"
position (O).
- Remove one of the cooking grids to gain access to the
burners.
- Turn on the gas supply (valve or lever on the regulator).
- Put a lighted match in front of the burner.
- Press, then rotate the knob corresponding to the burner
in a counter-clockwise direction to the (
) position.
- When the burner is lit, keep the control button depressed
for 10 seconds and then release it.
- Adjust the flame to the dimensions of the recipient by
using the two flow positions: HIGH (
) or LOW ( ).
Once the burner is lit, replace the grid or hotplate.
i) EXTINGUISHING THE BARBECUE
Set the control knobs to the "off" position (O), then close
the cylinder valve.
j) LIGHTING THE HOT PLATE (depending on model)
The hot plate can be used alone or at the same time as
the grill.
Lighting:
- Open the gas cylinder valve.
- Check gas circuit sealing from the frame to the hot plate
(see § f).
- Open the hotplate lid and retract it to the back of the
hotplate, sliding it in the grooves at the side.
- Press and rotate the control lever on the stove (
) to
its FULL FLOW position (
).
- Press the ignition button ( ) until the burner
lights. If the burner does not light after 10 seconds, put a
match to the edge of the burner.
- Adjust the flame to the dimensions of the recipient by
using the two flow positions: HIGH (
) or LOW ( ).
Do not use recipients with a diameter less than 10 cm or
over 24 cm.
k) TURNING OFF THE HOT PLATE
(depending on the model)
Return the control lever (
) to the OFF (O) position,
then close the valve on the gas bottle if the grill is not in
use.
To close the lid, slide it in its grooves, pulling it upwards
until it reaches the spindle, then tip it forwards.
l) LIGHTING OF THE CONSOLE (depending on the
model)
The lighting system of the console is powered by 4 type
AA (LR06) batteries provided with the barbecue grill. The
battery box is located on the front right-hand leg, behind
the right door. Remove the cover of the battery holder box
by sliding it upwards. Insert the batteries while respecting
the polarities indicated and then replace the cover.
To turn the lighting on or off, press on the stop-
start button located to the left of the console and
identified by this pictogram.
m) SIDE HOTPLATE GRILL
(depending on the model)
        
types of grill: a flat or corrugated grill.
         
saucepan stand. Light the hotplate and take advantage of
an additional grill surface.

flow to the hotplate burner by setting the control knob to
(
) or ( ).
n) REPLACING THE GAS CYLINDER
- always work in a well ventilated area and never in the
presence of a flame, spark or heat source.
- return the control knobs in the "off" position (O) then
close the cylinder valve.
- remove the regulator, check that the sealing joint is in
good condition.
- put the full cylinder in place, refit the regulator, taking
care not to apply stress to the hose. Check for gas leaks.
o) OPERATION

components which may be very hot.
10
GB
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Campingaz 4 Series RBS ESTATE LXS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Campingaz 4 Series RBS ESTATE LXS in the language / languages: All languages as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info