656741
5
Zoom out
Zoom in
Previous page
1/16
Next page
851Eazur
ENGLISH
5
Mains Voltage Selector Switch:
100-120V/220-240V AC~50/60Hz
Power AC
R
L
R
L
Trigger Out
2
1
Trigger
In InIn Out
Rec Out
Sub Out
Rec InSource 7Source 6Source 5Source 4
Rec OutRec In Source 7 Source 6 Source 5 Source 4
RS232C
Control Bus IR Emitter
GND
On Off
Power
GND
azur 851E Pre-Amplifier
Rated Power Consumption: 36W
www.cambridge-audio.com
Designed and engineered in London, England
LeftRight
Source 3
LeftRight
Source 2
LeftRight
Source 1
LeftRight
Left Right
(Balanced) (Unbalanced)
(Balanced) (Unbalanced)
(Balanced) (Unbalanced) (Balanced) (Unbalanced)
Pre Out
Rear panel connections
3
2
1 4
5 6
7
9 10 11 12
13
8
1
Power On/Off
Switches the unit on and off.
This product has APD (Auto Power Down) enabled as default. After
inactivity of 30 minutes, the product will automatically switch to Standby.
See later section for further details.
2
Mains Voltage Selector Switch
Switches the 851E mains voltage between 100-120V and 220-240V.
Note: Intended for use by a professional installer or Cambridge Audio
retailer only.
3
AC power socket
Once you have completed all connections to the unit, plug the AC power
cable into an appropriate mains socket then switch on. Your unit is now
ready for use.
4
RS232C
The RS232C port allows external serial control of the 851E, for use in a
custom installation. A full command set is available on the Cambridge
Audio website at www.cambridge-audio.com. This port can also be used
by Cambridge Audio service personnel for software updates.
5
Control Bus
In – Allows un-modulated commands from multi-room systems or other
components to be received by the unit.
Out – Loop out for Control Bus commands to another unit.
Also allows the 851E to turn on/off some Cambridge Audio units,
including the matching 851W power amplier. Refer to the 'Power
syncing' section of this manual for more information.
6
IR (Infra-Red) Emitter In
Allows modulated IR commands from multi-room systems or IR repeater
systems to be received by the unit. Commands received here are not
looped out of the Control Bus. Refer to the 'Custom installation' section
of this manual for more information.
7
Trigger In, Trigger Out 1 and 2
For custom install use, the 851E can be turned on and off (i.e. brought
in and out of Standby mode) by the presence of 5-12V DC at the Trigger
input. A trigger input or by turning the 851E on from the remote/front
panel will also produce an internally generated 12V DC trigger output
at the Trigger Out 1 and 2 connection. This can be used to turn on/
Standby a connected 851W power amplier if desired. Refer to the
'Power syncing' section of this manual for more information.
8
Source 1–3
Source 1–3 feature either unbalanced (phono/RCA) or balanced (XLR)
connections. Either type may be used but not both at the same time. The
balanced connection is the higher quality option and can reject noise
and interference in the cable when used with other equipment that
supports this function. An XLR connector is wired Pin 1 - Ground; Pin
2 - Hot (in-phase); Pin 3 - Cold (phase-inverted).
9
Pre Out
For connection to the balanced/unbalanced inputs of a power amplier.
10
Sub Out
Connect to the input on an active subwoofer if required.
11
Rec Out
Connect to the input sockets of your recording device.
12
Rec In (Source 8)
Connect to the output sockets of a Tape/MD player or other devices that
support recording.
13
Source 4–7
These inputs are suitable for any 'line level' source equipment such as
CD players, DAB or FM/AM tuners etc.
Note: These inputs are for analogue audio signals only. They should not
be connected to the digital output of a CD player or any other digital
device.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cambridge Audio AZUR 851E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cambridge Audio AZUR 851E in the language / languages: English as an attachment in your email.

The manual is 8,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cambridge Audio AZUR 851E

Cambridge Audio AZUR 851E User Manual - German - 16 pages

Cambridge Audio AZUR 851E User Manual - Dutch - 16 pages

Cambridge Audio AZUR 851E User Manual - French - 16 pages

Cambridge Audio AZUR 851E User Manual - Italian - 16 pages

Cambridge Audio AZUR 851E User Manual - Polish - 16 pages

Cambridge Audio AZUR 851E User Manual - Swedish - 16 pages

Cambridge Audio AZUR 851E User Manual - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info