763794
5
Zoom out
Zoom in
Previous page
1/26
Next page
azur 840A
Class XD Integrated Amplifier
User’s Manual
2 Azur Class XD integrated amplifier
Introduction .................................................................................................3
Safety precautions ......................................................................................4
Important safety instructions .....................................................................5
Rear panel connections..............................................................................6
Front panel controls....................................................................................8
Remote control..........................................................................................10
Connections ..............................................................................................11
Operating instructions ..............................................................................14
Amplifier setup..........................................................................................15
Multi-Room ................................................................................................18
Custom installation use............................................................................19
CAP5 protection system ...........................................................................20
Troubleshooting.........................................................................................22
Technical specifications ...........................................................................23
Limited warranty .......................................................................................24
CONTENTS
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 3
Thank
you
for
purchasing
this
Azur
840A
Class
XD
Integrated
Amplifier.
This
unit
is
part
of
our
new
'8'
Series
taking
Cambridge
Audio
to
new
levels
of
audio
excellence
as
part
of
our
commitment
to
the
on-ggoing
development
of
the
Azur
range.
We
hope
that
you
will
appreciate
the
results
and
enjoy
many
years
of
listening
pleasure
from
it.
For the 840A we developed many new circuits and components, with
many parts being designed specifically for this model. A unique
proprietary to Cambridge Audio patent pending amplifier topology has
even been developed called Class XD™ which can eliminate crossover
distortion at low signal levels.
This technology creates a region of pure Class-A operation where the
crossover zone would otherwise be. It should not be confused with Class
AB, which gives a small area of Class A, at the cost of higher distortion
as soon as signal levels moves outside it. Class XD circuitry not only
removes crossover distortion from the zero-crossing point but also
reduces distortion in the other parts of the amplifier's output range. A
white paper on this technology is available on our website:
www.cambridge-audio.com.
Please note that because of the Class XD technology the 840A runs
slightly warmer than a conventional Class B/AB amplifier and the
ventilation slots on the top of the unit must not be obscured.
Other features include the use of precision networks of resistors and
relays for the volume and balance control rather than the more common
solid-state or volume potentiometer schemes. Volume is controllable in
1 dB steps over most of the range, giving very fine control, an accurate
logarithmic law and superbly accurate channel balance. Input switching
is also by high quality relays.
The 840A features separate transformer secondaries for left and right
channels, twin rectifiers and separate PSU's for dual mono operation of the
left and right power amplifiers. A separate transformer supplies the preamp
making the 840A effectively a Pre and Power amp combination in one box.
Input 1 features a balanced input using XLRs giving optimal
performance with equipment such as the matching 840C Upsampling
CD player which feature balanced outputs.
A completely new casework has been designed which combines
massive structural rigidity with careful damping and control of acoustic
resonance. An Azur Navigator remote control is also provided, giving full
remote control of your amplifier in an attractive and easy to use
handset.
We have also added many new features, including support for multi-
room use. By plugging in one or two external Cambridge Audio Incognito
keypads and a power supply unit your amplifier can become the hub of
a simple multi-room system. In addition, Control Bus Input/Output, IR
Emitter Input and RS232 control are provided to make it easy to
integrate this unit into Custom Installation systems if desired.
Your amplifier can only be as good as the system it is connected to.
Please do not compromise on your source equipment, speakers or
cabling. Naturally we particularly recommend models from the
Cambridge Audio Azur range. These have been designed to the same
exacting standards as this amplifier. Your dealer can also supply
excellent quality Cambridge Audio interconnects to ensure your system
realises its full potential.
Thanks for taking the time to read this manual; we do recommend you
keep it for future reference.
Matthew Bramble
Technical Director
INTRODUCTION
4 Azur Class XD integrated amplifier
Checking
the
Power
Supply
Rating
For your own safety please read the following instructions carefully before attempting
to connect this unit to the mains.
Check that the rear of your unit indicates the correct supply voltage. If your mains
supply voltage is different, consult your dealer.
This unit is designed to operate only on the supply voltage and type that is
indicated on the rear panel of the unit. Connecting to other power sources may
damage the unit.
This equipment must be switched off when not in use and must not be used unless
correctly earthed. To reduce the risk of electric shock, do not remove the unit's
cover (or back). There are no user serviceable parts inside. Refer servicing to
qualified service personnel. If the power cord is fitted with a moulded mains plug
the unit must not be used if the plastic fuse carrier is not in place. Should you lose
the fuse carrier the correct part must be reordered from your Cambridge Audio
dealer.
The lightning flash with the arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of un-insulated
‘dangerous voltage’ within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
instructions in the service literature relevant to this appliance.
This product complies with European Low
Voltage (73/23/EEC) and Electromagnetic Compatibility
(89/336/EEC) Directives when used and installed according to
this instruction manual. For continued compliance only
Cambridge Audio accessories should be used with this product
and servicing must be referred to qualified service personnel.
The crossed-out wheeled bin is the European Union symbol for
indicating separate collection for electrical and electronic
equipment. This product contains electrical and electronic
equipment which should be reused, recycled or recovered and
should not be disposed of with unsorted regular waste. Please
return the unit or contact the authorised dealer from whom you
purchased this product for more information.
Plug
Fitting
Instructions
(UK Only)
The cord supplied with this appliance is factory fitted with a 13 amp mains plug
fitted with a 3 amp fuse inside. If it is necessary to change the fuse, it is important
that a 3 amp one is used. If the plug needs to be changed because it is not suitable
for your socket, or becomes damaged, it should be cut off and an appropriate plug
fitted following the wiring instructions below. The plug must then be disposed of
safely, as insertion into a 13 amp socket is likely to cause an electrical hazard.
Should it be necessary to fit a 3-pin BS mains plug to the power cord the wires
should be fitted as shown in this diagram. The colours of the wires in the mains
lead of this appliance may not correspond with the coloured markings identifying
the terminals in your plug. Connect them as follows:
The wire which is coloured BLUE must be connected to the terminal which is
marked with the letter ‘N’ or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is
marked with the letter ‘L’ or coloured RED.
The wire which is coloured GREEN/YELLOW must be connected to the terminal
which is marked with the letter ‘E’ or coloured GREEN.
If your model does not have an earth wire, then disregard this instruction.
If a 13amp (BS 1363) plug is used, a 3amp fuse must be fitted, or if any other type
of plug is used a 3amp or 5amp fuse must be fitted, either in the plug or adaptor,
or on the distribution board.
SAFETY PRECAUTIONS
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 5
IMPORTANT SAFETY INSTRUCTIONS
Please take a moment to read these notes before installing your Azur
amplifier, they will enable you to get the best performance and prolong
the life of the product. We advise you follow all instructions, heed all
warnings and keep the instructions for future reference.
The unit is of Class 1 construction and must be connected to a Mains
socket outlet with a protective earthing connection.
Only use the specified attachments/accessories with this unit.
Do not defeat the safety purpose of the polarized or grounding type plug.
A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or third prong are provided for your safety. If the provided
plug does not fit your outlet, consult an electrician for replacement of
the obsolete outlet.
The unit must be installed in a manner that makes disconnection of the
mains plug from the mains socket outlet (or appliance connector from the
rear of the unit) possible. Where the mains plug is used as the disconnect
device, the disconnect device shall remain readily operable. Protect the
power cord from being walked on or pinched particularly at plugs,
convenience repectacles, and the point where they exit from the unit.
This unit must be installed on a sturdy, level surface. Do not
place in a sealed area such as a bookcase or in a cabinet. Any
space open at the back (such as a dedicated equipment rack)
is fine however. When a cart is used, use caution when moving
the cart to avoid injury from tip-over.
Please ensure there is ample ventilation (at least 10cm clearance all
round). Do not put any objects on top of this unit. Do not situate it on a
rug or other soft surface and do not obstruct any air inlets or outlet
grilles. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce
heat. Do not stack multiple units on top of each other. Do not place in
an enclosed area such as a bookcase or in a cabinet without sufficient
ventilation.
WARNING - To reduce the risk of fire or electric shock, do not expose this
unit to rain or moisture. This unit must not be used near water or
exposed to dripping or splashing water or other liquids. No objects filled
with liquid, such as vases, shall be placed on the unit. In the event,
switch off immediately, disconnect from the mains supply and contact
your dealer for advice.
Ensure that small objects do not fall through any ventilation grille. If this
happens, switch off immediately, disconnect from the mains supply and
contact your dealer for advice.
To turn the unit off completely switch off on the rear panel. If you do not
intend to use this unit for a long period of time, unplug it from the mains
socket. Unplug this unit during lightning storms.
To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any
cleaning fluids containing alcohol, ammonia or abrasives. Do not spray
an aerosol at or near the amplifier.
This unit is not user serviceable, never attempt to repair, disassemble or
reconstruct the unit if there seems to be a problem. Servicing is required
when the unit has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into it,
the unit has been exposed to rain or moisture, does not operate
normally or has been dropped. A serious electric shock could result if
this precautionary measure is ignored.
This unit should be installed on a sturdy, level surface. Due to stray
magnetic fields turntables or CRT TV’s should not be located nearby due
to possible interference.
6 Azur Class XD integrated amplifier
Power
On/Off
Switches the unit on and off.
AC power
socket
Once you have completed all connections to the amplifier, plug the AC
power cable into an appropriate mains socket then switch on. Your
amplifier is now ready for use.
Loudspeaker
terminals
Two sets of loudspeaker terminals are available, A(main loudspeaker
terminals) and B(secondary loudspeaker terminals). Both sets of
speakers can be turned on and off. Connect the wires from your left
channel loudspeaker to the LEFT + & - terminals, and the wires from the
right channel loudspeaker to the RIGHT + & - terminals. In each case,
the red terminal is the positive output and the black terminal is the
negative output.
Care should be taken to ensure no stray strands of wire short the speaker
outputs together. Please ensure that the loudspeaker terminals have been
tightened completely to provide a good electrical connection. It is possible
for the sound quality to be affected if the screw terminals are loose.
Note: When using one pair of speakers, use speakers with a nominal
impedance of between 4-8 ohms. When using two pairs of speakers,
use speakers with a nominal impedance of between 6-8 ohms.
IR
(Infrared)
Emitter
In
Allows modulated IR commands from multi-room systems to be received
by the amplifier. Commands received here are not looped out of the
Control Bus. Refer to the ‘Custom Installation’ section for more
information.
Control
Bus
In
-Allows un-modulated commands from multi-rooms systems or other
components to be received by the unit.
Out
-Loop out for control bus commands to another unit. Also allows the
840A to control some Cambridge Audio units.
+
_
+
__
Right
Right
Right
Right
+
_
+
Left
Left
Left
Left
Right
Left
Right
Left
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In In Out
Right Left
RightLeft
Preamp OutTape OutTape InInput 7Input 6Input 5Input 4Input 3Input 2Input 1
Preamp Out Tape Out Tape In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Loudspeaker Terminals
Impedance 4 - 8 ohms
Input 1 Balanced Audio
RS232C
Control Bus
Power
PSU
In
International Patent Pending
LeisureTech Electronics Pty Ltd
Please ensure that loudspeaker terminals are fully tightened
Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
B
B
A
A
GND
www.cambridge-audio.com
Manufactured in an ISO9002 approved facility
Power AC
Designed in London, England
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
azur 840A Class XD Integrated Amplifier
Power Rating: 230V AC ~ 50Hz
Max Power Consumption: 800W
On Off
N2409
REAR PANEL CONNECTIONS
1
2
3
1
2
3
48
6
4
7
109
5
5
11
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 7
RS232C
The RS232C port allows external serial control of the 840A for custom
install use. A full command set is available on the Cambridge Audio
website at www.cambridge-aaudio.com. This port can also be used by
Cambridge Audio service personnel for software updates.
A-BBUS™
Ready/Incognito
Ready™
multi-rroom
outputs
PSU
-Connect an Incognito PS10 to supply power to the connected
multi-room keypads/speakers.
Keypad
1/2
-Connect one or two Incognito A-BUS KP10 keypads (or
other A-BUS compatible keypads) using CAT5/5e cable. Incognito AS10
Active Ceiling Speakers can also be connected here.
IR
-Four IR outputs for remote control of source equipment.
Please refer to the ‘Multi-Room’ section of this manual for more
information on connections and set-ups.
Input
1
Balanced
Audio
Input 1 features either unbalanced (phono/RCA) or balanced (XLR)
connections. Either type may be used but not both at the same time. The
balanced connection is the higher quality option and can reject noise
and interference in the cable when used with other equipment that
supports this function. An XLR connector is wired Pin 1 - Ground; Pin 2 -
Hot (in-phase); Pin 3 - Cold (phase-inverted).
When using either the balanced or unbalanced input, make sure that no
cables or equipment are connected to the unused input, as this may
degrade operation. The unused input does not require to be terminated
and this should not be done.
Preamp
Out
Connect these sockets to the inputs on an external power amplifier(s) or
active subwoofers etc.
Tape
In/Out
Connect to a tape deck or to the analog output sockets on a MiniDisc,
portable digital music player or CD recorder using an interconnect cable
from the recorder's Line Out sockets to the amplifier's Tape In sockets.
The Tape Input circuit of the 840A is a "monitor" type, different from the
other 7 inputs. For the 7 normal inputs, the source selected for listening
to will be sent out of the Tape Out for recording. The source currently
being listened to and (optionally) recorded is then shown on the front
panel display.
However, when the Tape Input is selected a solid circle will appear
beside TAPE MON indicating that the Tape Input is now being listened to
with a different source being sent out of the Tape Out for recording. The
recording source is also shown by a solid circle by the selected input and
can be changed by pressing the other source buttons. To switch Tape
Monitor off, simply press the Tape Mon input select button again,
toggling this function off.
This feature is most useful when using 3-head analog cassette decks
which allow the signal being recorded to be played back live off tape (via
a 3rd head) whilst it is simultaneously recorded. It is then possible by
toggling the Tape Monitor input on and off to compare directly in real
time the original and recorded signal so that adjustments to the
recording parameters of the tape machine can be made (consult the
manual of your 3-head analog cassette deck for full details).
Inputs
1-77
These inputs are suitable for any 'line level' source equipment such as
CD players, DAB or FM/AM tuners etc.
Note: These inputs are for analog audio signals only. They should not be
connected to the digital output of a CD player or any other digital device.
6
7
8
9
10
11
8 Azur Class XD integrated amplifier
Standby/On
Switches the unit between Standby mode (indicated by dim power LED)
and On (indicated by bright power LED). Standby is a low power mode
where the power consumption is less than 10 Watts. The unit should be
left in Standby mode when not in use.
Phones
Allows for the connection of stereo headphones with a ¼" Jack plug.
Headphones with an impedance of between 32 and 600 ohms are
recommended. When the headphones are connected, the loudspeaker
relays are released switching off the output to the loudspeakers
(speakers A and B).
Speaker
A/B
Press to scroll through the speaker sets connected to the loudspeaker
terminals on the back panel (speaker sets A, B or A and B). This can be
used for listening to an extra set of loudspeakers in another room.
Please note that care should be taken when choosing speakers if two
loudspeakers are going to be used on each channel. If the combined
resistance measured on the loudspeaker terminals is too low the
amplifier may not switch out of Standby mode until a suitable load
resistance is detected. For more information refer to the CAP5 section of
this manual.
Note: When using one pair of speakers, use speakers with a nominal
impedance of between 4-8 ohms. When using two pairs of speakers,
use speakers with a nominal impedance of between 6-8 ohms each.
Volume
Bass Treble DirectModeSpeaker A/BPhonesStandby / On
azur 840A
Class XD Integrated Amplifier
FRONT PANEL CONTROLS
13
2
1 2 3 4 6
8
79 10
11
5
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 9
Mode
Press to switch between Volume and Balance modes. Press and hold to
to enter the 840A system configure menu.
Infrared
sensor
Receives IR commands from the supplied Azur remote control. A clear
unobstructed line of sight between the remote control and the sensor is
required.
&
Input
select
buttons
Push the appropriate input selection button to select the source
component that you wish to listen to (highlighted by a solid circle on the
display). The signal selected is also fed to the Tape Out sockets so that
it may be recorded. The input should not be changed whilst recording
(but the recorded signal can be checked using the tape input Tape
Monitor).
Display
LCD used to control the 840A. Please refer to the ‘Operating
instructions’ and ‘Amplifier setup’ section of this manual for more
information.
Bass
and
Treble
Press to release and rotate to allow subtle adjustments to the tonal
balance of the sound.
Direct
This control gives the audio signal a more direct path to the power
amplifier stage of your amplifier, bypassing the tone control circuits for
the purest possible sound quality.
Volume
Use to increase/decrease the level of the sound from the outputs of the
amplifier. This control affects the level of the loudspeaker output, the
pre-amp output and the headphone output. It does not affect the Tape
Out connections. It is advisable to turn the Volume control fully anti-
clockwise before switching the amplifier on.
The Volume control is also used in navigating the 840A System
Configure menus on the front panel display.
Please
refer
to
the
‘Operating
instructions’
section
of
this
manual
for
more
information
on
some
functions
of
these
buttons.
4
5
6 7
8
9
10
11
10 Azur Class XD integrated amplifier
The 840A is supplied with an Azur Navigator remote control that
operates both this amplifier and Cambridge Audio Azur CD
players. Insert the supplied AAA batteries to activate.
The 840A/C remote control comes with an Amplifier
Control button, that when pressed, puts the remote into
Amp
mode, allowing operation of the 840A. When
pressed, the LED will light up for 7 seconds (to let you
know you are in Amp mode), and will then flash when one
of the circled Amp buttons is pressed. All other remote
buttons are inactive when in Amp mode.
The functions relevant to the amplifier are as follows:
Standby/On
Switches the amplifier between On and Standby mode.
Numerical
buttons
1-88
Press to change the input source to the amplifier. Button 8
toggles Tape Monitor on/off.
Mode
Press to switch between Volume and Balance modes.
REMOTE CONTROL
Mute
Mutes the audio on the amplifier. The mute mode is indicated by
MUTE appearing and the volume level being replaced by two
flashing dashes in the display. Press again to cancel mute.
Volume
Increase or decrease the volume of the amplifier output.
Speaker
A/B
Press to scroll through the speaker sets connected to the
loudspeaker terminals on the back panel (speaker sets A, B or A
and B).
Bright
Adjust the backlight of the front panel display; bright, dim or off.
To exit Amp mode (and return to CD mode), press the Amp Control
button again (the LED will light up for one second).
Vol
Vol
Random
Repeat
Select
RemainA - B
Menu
Space
Speaker
A/B
Intro
Mode
Prog
Amp
Control
Mode
Speaker
A/B
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 11
When designing our amplifiers we have tried to include features that
allow you to connect your system in various ways. The inclusion of
features such as Pre-Out and Speaker B connections mean that you can
flexibly configure your system depending on your requirements. The
following diagrams are designed to make connection easy.
Basic
connection
The diagram below shows the basic connection of your amplifier to a CD
player and a pair of loudspeakers.
CONNECTIONS
+
_
+
__
Right
Right
Right
Right
+
_
+
Left
Left
Left
Left
Right
Left
Right
Left
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In In Out
Right Left
RightLeft
Preamp OutTape OutTape InInput 7Input 6Input 5Input 4Input 3Input 2Input 1
Preamp Out Tape Out Tape In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Loudspeaker Terminals
Impedance 4 - 8 ohms
Input 1 Balanced Audio
RS232C
Control Bus
Power
PSU
In
International Patent Pending
LeisureTech Electronics Pty Ltd
Please ensure that loudspeaker terminals are fully tightened
Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
B
B
A
A
GND
www.cambridge-audio.com
Manufactured in an ISO9002 approved facility
Power AC
Designed in London, England
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
azur 840A Class XD Integrated Amplifier
Power Rating: 230V AC ~ 50Hz
Max Power Consumption: 800W
On Off
N2409
Digital Outputs
Power AC
Designed in London, England
azur 840C Upsampling Compact Disc Player
Max Power Consumption: 40W
www.cambridge-audio.com
RS232C
IR Emitter
InIn Out
Control Bus
S/P DIF
Co-axial
Toslink
Optical
Digital Input 1
Right Left
RightLef t
Balanced Audio OutUnbalanced Audio Out
S/P DIF
Co-axial
Toslink
Optical
Digital Input 2
S/P DIF
Co-axial
Toslink
Optical
Right
Left
Right
Left
Manufactured in an
ISO9002 approved facility
On Off
Power
Class 1 Laser Product
Luokan 1 Laserplaite
Klass 1 Laserapparat
Mains Voltage Selector Switch
115V/230V AC~50/60Hz
N2409
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
GND
884400CC
884400AA
Tape
connection
The diagram below shows how to connect the amplifier to a tape
recorder or other source with a record and monitor connection.
Please note that either of the tape loop outputs can be used (as they are
both the same signal in parallel).
+
_
+
__
Right
Right
Right
Right
+
_
+
Left
Left
Left
Left
Right
Left
Right
Left
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In In Out
Right Left
RightLeft
Preamp OutTape OutTape InInput 7Input 6Input 5Input 4Input 3Input 2Input 1
Preamp Out Tape Out Tape In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Loudspeaker Terminals
Impedance 4 - 8 ohms
Input 1 Balanced Audio
RS232C
Control Bus
Power
PSU
In
International Patent Pending
LeisureTech Electronics Pty Ltd
Please ensure that loudspeaker terminals are fully tightened
Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
B
B
A
A
GND
www.cambridge-audio.com
Manufactured in an ISO9002 approved facility
Power AC
Designed in London, England
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
azur 840A Class XD Integrated Amplifier
Power Rating: 230V AC ~ 50Hz
Max Power Consumption: 800W
On Off
N2409
Rec OutRec In
TTaappee
//
MMDDPPllaayyeerr
884400AA
12 Azur Class XD integrated amplifier
CONNECTIONS (CONTINUED)
Speaker
B connections
The Speaker B connections on the back of the amplifier allow for a
second set of speakers to be used (i.e. speakers located in another
room). The Speaker A/B button on the front panel allows this second set
of speakers to be switched on and off.
Note: When using two pairs of speakers, use speakers with a nominal
impedance of between 6-8 ohms each minimum.
Preamp
Out
connections
The Preamp Out sockets are for connecting to the input sockets of a
power amplifier or active subwoofer. The diagram below shows how to
connect the amplifier to an active subwoofer via the Line In inputs on the
subwoofer.
+
_
+
__
Right
Right
Right
Right
+
_
+
Left
Left
Left
Left
Right
Left
Right
Left
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In In Out
Right Left
RightLeft
Preamp OutTape OutTape InInput 7Input 6Input 5Input 4Input 3Input 2Input 1
Preamp Out Tape Out Tape In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Loudspeaker Terminals
Impedance 4 - 8 ohms
Input 1 Balanced Audio
RS232C
Control Bus
Power
PSU
In
International Patent Pending
LeisureTech Electronics Pty Ltd
Please ensure that loudspeaker terminals are fully tightened
Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
B
B
A
A
GND
www.cambridge-audio.com
Manufactured in an ISO9002 approved facility
Power AC
Designed in London, England
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
azur 840A Class XD Integrated Amplifier
Power Rating: 230V AC ~ 50Hz
Max Power Consumption: 800W
On Off
N2409
Digital Outputs
Power AC
Designed in London, England
azur 840C Upsampling Compact Disc Player
Max Power Consumption: 40W
www.cambridge-audio.com
RS232C
IR Emitter
InIn Out
Control Bus
S/P DIF
Co-axial
Toslink
Optical
Digital Input 1
Right Left
RightLef t
Balanced Audio OutUnbalanced Audio Out
S/P DIF
Co-axial
Toslink
Optical
Digital Input 2
S/P DIF
Co-axial
Toslink
Optical
Right
Left
Right
Left
Manufactured in an
ISO9002 approved facility
On Off
Power
Class 1 Laser Product
Luokan 1 Laserplaite
Klass 1 Laserapparat
Mains Voltage Selector Switch
115V/230V AC~50/60Hz
N2409
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
GND
+
_
+
__
Right
Right
Right
Right
+
_
+
Left
Left
Left
Left
Right
Left
Right
Left
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In In Out
Right Left
RightLeft
Preamp OutTape OutTape InInput 7Input 6Input 5Input 4Input 3Input 2Input 1
Preamp Out Tape Out Tape In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Loudspeaker Terminals
Impedance 4 - 8 ohms
Input 1 Balanced Audio
RS232C
Control Bus
Power
PSU
In
International Patent Pending
LeisureTech Electronics Pty Ltd
Please ensure that loudspeaker terminals are fully tightened
Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
B
B
A
A
GND
www.cambridge-audio.com
Manufactured in an ISO9002 approved facility
Power AC
Designed in London, England
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
azur 840A Class XD Integrated Amplifier
Power Rating: 230V AC ~ 50Hz
Max Power Consumption: 800W
On Off
N2409
Digital Outputs
Power AC
Designed in London, England
azur 840C Upsampling Compact Disc Player
Max Power Consumption: 40W
www.cambridge-audio.com
RS232C
IR Emitter
InIn Out
Control Bus
S/P DIF
Co-axial
Toslink
Optical
Digital Input 1
Right Left
RightLef t
Balanced Audio OutUnbalanced Audio Out
S/P DIF
Co-axial
Toslink
Optical
Digital Input 2
S/P DIF
Co-axial
Toslink
Optical
Right
Left
Right
Left
Manufactured in an
ISO9002 approved facility
On Off
Power
Class 1 Laser Product
Luokan 1 Laserplaite
Klass 1 Laserapparat
Mains Voltage Selector Switch
115V/230V AC~50/60Hz
N2409
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
GND
AAccttiivvee
ssuubbwwooooffeerr
884400CC
884400AA
884400CC
884400AA
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 13
Balanced
audio
connections
The diagram below shows how to connect the 840A to the Azur 840C
Upsampling CD player using the Balanced Audio inputs via three-pin XLR
connectors (Note: the 840A can also be connected to non-Cambridge
Audio sources with balanced outputs).
Balanced connections in an audio system are designed to reject
electrical noise, from power wiring etc, and also the effects of noise
currents flowing through ground connections. The basic principle of
+
_
+
__
Right
Right
Right
Right
+
_
+
Left
Left
Left
Left
Right
Left
Right
Left
IR1
IR2
IR3
IR4
Keypad 1
Keypad 2
Multi-Room
IR Emitter
In In Out
Right Left
RightLeft
Preamp OutTape OutTape InInput 7Input 6Input 5Input 4Input 3Input 2Input 1
Preamp Out Tape Out Tape In Input 7 Input 6 Input 5 Input 4 Input 3 Input 2 Input 1
Loudspeaker Terminals
Impedance 4 - 8 ohms
Input 1 Balanced Audio
RS232C
Control Bus
Power
PSU
In
International Patent Pending
LeisureTech Electronics Pty Ltd
Please ensure that loudspeaker terminals are fully tightened
Veuillez s'assurer que les bornes de l'enceinte sont entièrement serrées
B
B
A
A
GND
www.cambridge-audio.com
Manufactured in an ISO9002 approved facility
Power AC
Designed in London, England
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
azur 840A Class XD Integrated Amplifier
Power Rating: 230V AC ~ 50Hz
Max Power Consumption: 800W
On Off
N2409
Digital Outputs
Power AC
Designed in London, England
azur 840C Upsampling Compact Disc Player
Max Power Consumption: 40W
www.cambridge-audio.com
RS232C
IR Emitter
InIn Out
Control Bus
S/P DIF
Co-axial
Toslink
Optical
Digital Input 1
Right Left
RightLef t
Balanced Audio OutUnbalanced Audio Out
S/P DIF
Co-axial
Toslink
Optical
Digital Input 2
S/P DIF
Co-axial
Toslink
Optical
Right
Left
Right
Left
Manufactured in an
ISO9002 approved facility
On Off
Power
Class 1 Laser Product
Luokan 1 Laserplaite
Klass 1 Laserapparat
Mains Voltage Selector Switch
115V/230V AC~50/60Hz
N2409
Caution Risk of electric shock. Do not open.
Avis Risque de choc electrique. Ne pas ouvrir.
Achtung Vorm öffnen des gërates. Netzstecker ziehen.
GND
balanced interconnection is to get the signal you want by subtraction,
using a three-wire connection. One signal wire (the hot or in-phase)
carries the normal signal, while other (the cold or phase-inverted)
carries an inverted version. The balanced input senses the difference
between the two lines to give the wanted signal. Any noise voltages that
appear identically on both lines (these are called common-mode
signals) are cancelled by the subtraction. An additional advantage is
that the connection effectively carries twice the signal level and so
improves the signal-to-noise ratio.
The 840A and 840C are designed to work at their highest performance
when a balanced interconnect is used; high quality stereo XLR to XLR
interconnects should be used.
884400CC
884400AA
Balance
Press the Mode button to enter Balance mode. BALANCE will appear on
the display and can be adjusted using the volume control. Press the
Mode button again to return to Volume mode or wait 5 seconds for the
840A to automatically exit Balance mode.
Bass
and
Treble
These controls allow subtle adjustments to the tonal balance of the
sound. Press to release and rotate to adjust (press back in when desired
settings found). In the central position these controls have no effect.
These controls only modify the sound through your loudspeakers and
the Pre-Out sockets; they do not affect the signals sent through the Tape
Out connections. With a well produced CD and a good system the tone
controls are unnecessary and can be switched out by the Direct switch.
This completely removes them from the signal path for maximum
fidelity. If the musical recording is of poor quality or other factors are
affecting the sound quality, it may be necessary to adjust the tone
controls to compensate.
The 840A has a custom-made display on the front of the unit showing
the current status and allowing you to access the 840A System
Configure menus. Here you can adjust the listening settings of the
amplifier to personal preference. The menu system is easy to navigate
and control, simply by using the input select buttons to turn a feature on
(solid circle) or off (no circle) and the volume control knob to
increase/decrease settings.
Volume
Adjust the volume control knob on the front panel (or using the remote
control). The display will show the change in volume in decibels (dB).
‘OdB’ indicates maximum volume while lower volume settings progress
into the negative range. This can also be changed to volume units (0-72)
in the System Configure menu.
Speaker
A/B
Press the Speaker A/B button to scroll through the speaker sets
connected via the rear panel: speakers A, B or A and B.
14 Azur Class XD integrated amplifier
OPERATING INSTRUCTIONS
Speaker A/B
Volume
Mode
Volume
Mode
Volume
Bass Treble Direct
840A Class XD integrated amplifier
Azur Class XD integrated amplifier 21
It is possible to disable the short circuit detection feature by pressing the
SHORT DT button to off when in the 840A System Configure menu. This
would only be required if the loudspeakers have very low DC resistance.
5.
Intelligent
clipping
detection
Indication - Volume is reduced automatically, “CLIPPING” appears on
the front panel display.
Description - CAP5 has the ability to detect when the amplifier starts to
clip or overdrive at its output, which can damage loudspeakers, and
degrade the sound. Clipping distortion
is caused at high volume levels when
the output signal attempts to go
outside the maximum voltage that the
amplifier can provide, causing the tops
of the signal to flatten off. When CAP5
detects clipping the volume will be
automatically reduced down until CAP5
detects an undistorted output.
It is possible to disable the clipping detection feature by pressing the
CLIP DT button to off when in the 840A System Configure menu.
Note: Disabling the clipping detection is not advised as this feature has
been added deliberately to protect the amplifier and loudspeakers.
"OVERLOAD" indication. The amplifier will stay in this state until the
Standby/ON switch is pressed to reset it.
Remedy - The resistance on the loudspeaker terminals is too low. Check
to see if there is a short circuit between the loudspeaker terminals.
Note: If the indication remains the same and multiple loudspeakers are
being used on each loudspeaker output then please remove a pair and
retry. If too many loudspeakers are connected to any amplifier causing
the load resistance to drop too low the amplifier will be overloaded.
CAP5 will detect this situation. If the indication remains the same with
only one set of loudspeakers connected, there may be a fault with one
or both of the loudspeakers.
4.
Short
circuit
detection
Indication - Unit has not come out of Standby, display flashes “SPKR
SHORT”.
Description - During power up from Standby CAP5 performs a check on
the loudspeaker terminals to see if a short across the terminals has
been accidentally introduced (display flashes “SPKR CHECK”). If the
resistance measured across the loudspeaker terminals is too low the
unit will stay in Standby mode until the fault has been removed and
Power up is re-attempted (display flashes “SPKR SHORT”).
Remedy - User related fault. There may be a short circuit between the
loudspeaker terminals. Check all loudspeaker connections before
attempting to switch the unit out of Standby (display will flash “SPKR
CHECK” then “SPKR OK” when short circuit fixed).
Mode
Volume
Mode
Volume
CClliippppiinngg
azur 840A
Part No. AP18646/2
www.cambridge-aaudio.com
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cambridge Audio Azur 840A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cambridge Audio Azur 840A in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cambridge Audio Azur 840A

Cambridge Audio Azur 840A User Manual - German - 26 pages

Cambridge Audio Azur 840A User Manual - Dutch - 26 pages

Cambridge Audio Azur 840A User Manual - Danish - 26 pages

Cambridge Audio Azur 840A User Manual - Italian - 26 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info