581025
30
Zoom out
Zoom in
Previous page
1/40
Next page
30
You can use the Volume knob or the Vol and Vol buttons to make
changes to the picture or press the Pic.Adj. button again to move to the next
item.
Adjustments are available for Brightness, Contrast, Saturation, Sharpness
and Y/C Delay.
A second feature of the Picture Adjustment button on the unit's front panel
is setting the output resolution for the scaler (this can also be done in the
OSD see earlier section).
If the front panel (not remote) button is pressed and held for approx. 10
seconds the 751R V2 will show the current scaler output resolution on the
751R V2's front panel display. Holding for a further 10 seconds will change
the output resolution to the next available one (and allow time for the TV to
re-sync).
Holding further will continue the process and the video output will gradually
move through all possible resolutions 480p 60Hz, 576p 50Hz, 720p 50Hz,
720p 60Hz, 1080i 50Hz, 1080i 60Hz, 1080p 50Hz and 1080p 60Hz (and
back round).
This feature can be useful if the scaler output is accidentally set to a
resolution your TV does not support and picture is lost.
By pressing and holding the Pic.Adj. button, you can cause the 751R V2 to
scroll through all resolutions automatically. Simply let go of the button when
a visible video image at a suitable resolution appears.
Audio split mode
In some circumstances the 751R V2 is able to allow the user to view one
source whilst listening to another. For instance you could watch the video
of a sports channel whilst getting an audio commentary from another such
as the Tuner.
To perform Audio Split:
1. Select the source you wish to watch in the normal way.
2. Press and hold the button on the front panel (not remote) for the source
you wish to listen to. After 4 seconds approx "Audio Split" will scroll across
the display and you will now be listening to that source instead. Video will
not have changed.
1 2
The 751R V2 allows splitting from any source whatever its video input
type (Composite, S-Video, Component or HDMI) but only to sources where
analogue or digital audio is the current audio input type, not HDMI.
If the combination is not allowed "Mode Unavailable" will instead scroll
across the display and no change will be made. To cancel audio split mode
simply select a new source and normal operation will be resumed.
HDMI A and B outputs
The 751R V2 has two HDMI outputs allowing the connection of two TVs
or a TV and projector etc. Both outputs show the same picture. HDMI A
also features an Audio Return Channel for TVs that feature this (see earlier
section).
To switch between only HDMI A active, HDMI B active or HDMI A and B both
active select the HDMI/Component Assign menu in the OSD and highlight
the HDMI Out menu item. Use the left and right buttons to scroll though the
options.
HDMI/Component Assign
HDMI 1 :
HDMI 2 :
HDMI 3 :
HDMI 4 :
HDMI 5 :
Component 1 :
Component 2 :
Component 3 :
HDMI Out :
Return I/O
BD/DVD
VIDEO 1
VIDEO 2
Recorder 1
AUX
BD/DVD
VIDEO 1
VIDEO 2
A+B
Alternatively, press and hold the Pic. Adj. button when the OSD is on, scrolls
the output from HDMI A to HDMI B to HDMI A+B and so on.
Note: The 751R V2 also shows the active HDMI outputs on the front panel
display of the unit itself whenever the OSD is on.
This is so you can still see what the active outputs are even if the OSD
disappears if you turn off the HDMI output you have connected to your TV.
HDMI bypass
The 751R V2 features an HDMI bypass mode that copies the incoming HDMI
to the output without internal reception or processing.
This does not necessarily mean all future standards will pass through
however if they use new pixel clock rates or bit depths that the 751R V2
HDMI 1.4 chipset cannot support.
This feature has been included to allow some measure of compatibility with
any future unsupported audio/video formats as they can be sent directly to
the TV/Projector.
It can also be useful if you have a TV with built in speakers and would like to
send the incoming source to the TV for decoding rather than have the 751R
V2 do the decoding.
To select HDMI Bypass select the Advanced Setup menu from the main
OSD screen, then the Advanced Audio menu and highlight the HDMI Bypass
menu item.
Uses the buttons to switch between Normal (HDMI reception) and
Bypass modes.
Advanced Audio Setup
Multi Ch.Out :
HDMI Bypass :
TV ARC(HDMIA) :
Auto Power Down :
Return I/O
Normal
Bypass
Disable
Enable
Trigger outputs
The 751R V2 feature two trigger outputs that can be used to signal to
external devices for simple automation functions.
Examples might be using the Triggers to open or close curtains, tell a
projection screen to roll up and down or turning on/off external power amps
etc.
The outputs are 0V for Off and 12V for On at up to 100mA. The connections
are 3.5mm mono mini-jacks, with the tip as the output, ring as ground.
To choose how the triggers operate select the Advanced Setup menu from
the Main Menu, then select the Trigger A (or Trigger B) menu item, the
options are:
Advanced Setup Menus
Advanced Audio
Input Name Assign
Advanced Dolby/DTS
Advanced Audyssey
Trigger A
Trigger B
OSD Setup/SW Version
Return I/O
Manual Select: Yes/No When enabled this means the trigger output can
be toggled On and Off by the matching Trigger button on the remote control.
If disabled these buttons will have no effect.
Note: When enabled the remote buttons can be used to toggle the outputs
(override the status) even if they are also following the status of a zone or
source selection as below.
Follow Standby: Yes/No/Zone 2 this means the trigger output can follow
the On/Off status of the Main Zone or alternatively that of Zone 2.
Sources: Yes/No the trigger output can be made to go high when one or
more specic sources is selected.
Note: Follow Standby and selecting any Sources are mutually exclusive
options.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cambridge 751RV2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cambridge 751RV2 in the language / languages: English as an attachment in your email.

The manual is 12,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cambridge 751RV2

Cambridge 751RV2 User Manual - German - 40 pages

Cambridge 751RV2 User Manual - Dutch - 40 pages

Cambridge 751RV2 User Manual - French - 40 pages

Cambridge 751RV2 User Manual - Italian - 40 pages

Cambridge 751RV2 User Manual - Polish - 40 pages

Cambridge 751RV2 User Manual - Swedish - 40 pages

Cambridge 751RV2 User Manual - Spanish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info