497332

Caliber RMD 571 Manual

10
Zoom out
Zoom in
Previous page
1/17
Next page
99
3. TUNE/SEEK UP/DOWN BUTTONS
In RADIO mode:
1) Long press the >>| or |<< button to automatically search up or down for a
available station from the current frequency.
2) Briefly press the >>| or |<< button to manually search up or down with step
by step for your desired station from the current frequency.
4. APS BUTTON
In RADIO mode:
1) When long pressing the APS button, the radio searches from the lowest
frequency and checks the signal strength level until 1 cycle search is finished.
And then the 6 strongest stations are preset to the corresponding preset
number memory bank. The AS operation is implemented in each bank of the
selected band. When the AS operation is finished, it will scan each preset station
for 5 seconds in FM or MW band from M1 when APS button is pressed briefly.
After the scanning is finished, broadcasting will resume on the M1.(It can store
3x6 stations for FM and 2x6 stations for MW)
2) When pressing the APS button briefly, the radio will scan each preset station
for 5 seconds in FM or MW band from M1.
After finishing a circle of scanning, it will resume broadcasting on the M1.
NOTE: In FM band, FM1,FM2,FM3 is checked one at a time; In MW band,
MW1, MW2 is checked one at a time.
5. PRESET STATION [ 1-6 ] BUTTONS
In RADIO mode:
1) To memorize the current frequency on the current band, long press any of the
number buttons (1-6) on remote control or on the front panel .
2) To recall the preset memory on the current band, briefly press one of the preset
buttons [1-6] on remote control or on the front panel.
6. STEREO/MONO BUTTON
Press the ST button on the remote control to select the STEREO or MONO
sound mode for FM band.
7. LOC BUTTON
1) In RADIO mode, when the signal of the distance radio station are very weak
and the receiving effect is bad during tuning. If there is the word LOC on the
monitor, press this button to turn off the LOC function, then tune again for the
distance radio station;
2) In RADIO mode, when the signal of the local radio stations are too strong and
the interference does no t allow the tuner to lock on stations, press this button
to turn on the LOC function to display the word LOC on the monitor, then tune
again for the local radio stations.
8. PTY (PROGRAM TYPE) BUTTON
Press the PTY button shortly to select one of the following mode:
PTY MUSIC group- - PTY SPEECH group -- OFF
1010
When PTY group is on, press the VOL+ or VOL- button on the remote control
or rotate the VOL knob on the front panel to select one of PTY programs
as follows:
<-->NEWS<-->AFFAIRS<-->INFO<-->SPORT<-->EDUCATE<-->DRAMA
<-->CULTURE <-->SCIENCE<--> VARIED<-->WEATHER<--> FINANCE
<-->CHILDREN<-->SOCIAL<-->RELIGION<-->PHONE IN<-->TRAVEL
<-->LEISURE<-->DOCUMENT< -->PTY NONE<-->POP M< -->ROCK M
<-->EASY M<-->LIGHT M<--> CLASSICS<-->OTHER M
<-->JAZZ<-->COUNTRY<-->NATION M<-->OLDIES<-->FOLK M<-->
When PTY group is on, pressing the 6 number buttons also can select one of
PTY programs as above.
After selecting one of the PTY programs, it will display SEEK PTY and
automatically search for the station of the PTY program. If the station of the
PTY program does not exist, it will display PTY NONE and then return back to
the normal station.
9. AF [ALTERNATIVE FREQUENCIES] BUTTON
When AF button is pressed briefly, the AF switching mode is selected and the
status of the AF switching mode is displayed by AF segment on the display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not
received yet.
When the AF switching mode is selected, the radio checks the signal strength
of the AF all the time. The interval of checking time of each AFs depends on
the signal strength of the current station, from a few minute for the strong
station to a few seconds for the weak station. Every time when a new AF is
stronger than the current station, it switches over to that frequency for very
short time, and the NEW FREQUENCY is displayed for 1-2 second. Because
the mute time of the AF switching or the checking time is very short, it is almost
inaudible in case of normal program. (When AF flashes on the monitor, it will
search for the stronger RDS station. If AF and TP flash on the monitor, it can
only search for the traffic announcement station).
In FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY functions can
only receive and save the RDS program.
10. TA [TRAFFIC ANNOUNCEMENT] BUTTON
Press the TA button briefly to turn on TA search mode.
When traffic announcement is transmitted:
1).If the unit is in Disc Play mode, it will switch to radio mode temporarily.
2).Temporarily switches over to an station with traffic announcement, and TA,
TP will be displayed on the monitor.
* TA interruption function:
The current traffic announcement is cancelled by pressing TA button briefly.
* When TA is on, SEEK, (SCAN), AUTO MEMORY functions can be received
or saved only when traffic program identification code has been received.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber RMD 571 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber RMD 571 in the language / languages: English as an attachment in your email.

The manual is 5,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber RMD 571

Caliber RMD 571 Quick start guide - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info