497373
19
Zoom out
Zoom in
Previous page
1/24
Next page
18
announcement on or off.
TA mode: Seek, Alarm
Touch [Seek] or [Alarm] to select traffic
announcement’s active mode.
REG: On, Off
Touch [On] or [Off] to select whether identify
the regional code when tuning.
RDS CT: On, Off
Touch [On] or [Off] to select whether
synchronize clock time with the signal source.
BT Setting
Pair: On, Off
Touch [On] or [Off] to choose pair
automatically on or off.
Auto Connect: On, Off
Touch [On] or [Off] to choose connect
automatically on or off.
Auto Answer: On, Off
Touch [On] or [Off] to choose answer
automatically on or off.
PIN Code: Set
Touch [Set] button to open keypad, then
set the bluetooth password by the number
buttons. Touch
KEY PAD
13800138000
1
23
456
789
*
0#
the erase previous
number. Touch
KEY PAD
13800138000
1
23
456
789
*
0#
to conrm .The original
password is “1234”.
To reset the password, you should enter
the original password first, then input a new
password, touch
KEY PAD
13800138000
1
23
456
789
*
0#
to conrm, input the
password again to conrm.
Other Setting
SWC (Steering Wheel Control)
refer to <Basic Operations>.
TS: Adjust
Touch [Adjust] to calibrate the screen.
When the touch operation is not sensitive or
valid, you should calibrate the touch screen
through “TS Calibrate” function.
System Setup
(continued)
Device Connections
Notes of connection
This unit is designed to be used in a
vehicle with a 12-volt battery and negative
grounding. Before installing this unit to a
recreational vehicle, a bus, or a truck, make
sure the battery voltage is appropriate for
this unit to be used, otherwise, install a
transformer by professional to convert the
output voltage to 12V.
To avoid short circuit in the electrical
system, ensure that the negative battery
cable is disconnected before installation.
To prevent short circuit in the wiring and
damaging to this unit, secure all wirings
with cable clamp or adhesive tape. Route
the wirings in a secured, out of heating
place without touching any moving parts
such as gear shift, handbrake, and seat
rails to prevent the wiring insulation being
melted / worn off.
Never pass the yellow power cord through
the installation hole into the engine
compartment and connect to the car
battery. Otherwise, a high possibility of
serious short circuit to the electrical system
may occur.
Replacing a new fuse with 15A rating
when the old one is broken, using no
fuse or fuse with improper rating may
cause damage to this unit or even fires.
If a proper fuse is installed and electrical
problems still occur, please contact your
local authorised service agent.
DO NOT connect other equipments with
the car battery to avoid battery overheating.
Please make sure all the wiring
connections & the cables of the Speakers
are well-insulated. Otherwise, this unit may
be damaged by short circuit.
If there is no ACC available, please
connect ACC lead to the power supply with
a switch.
If an external power amplier is connected,
please don't connect P.CONT lead to the
power lead of the external power amplier,
otherwise, electric spark or other damage
may result.
Never ground the speaker output to
prevent the damage to the built-in power
amplier.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber RDD883BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber RDD883BT in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber RDD883BT

Caliber RDD883BT Quick start guide - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info