781576
6
Zoom out
Zoom in
Previous page
1/28
Next page
7. Reconnect the wire harness and the
antenna and be careful not to pinch any
wires or cables.
8. Slide the unit into the sleeve until it
locks into place.
9. To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap to
the mounting bolt on the back of the unit.
If necessary, bend the metal strap to fit
your vehicle's mounting area. Then use
the supplied hardware (Tapping Screw
(5x25mm) and Plain Washer) to attach
the other end of metal strap to a solid
metal part of the vehicle under the
dashboard. This strap also helps ensure
proper electrical grounding of the unit.
Note to install the short threading
terminal of the mounting bolt to the back
of the unit and the other long threading
terminal to the dashboard.
6. Mount the sleeve by inserting the
sleeve into the opening of the dashboard
and bend open the tabs located around
the sleeve with a screwdriver. Not all tabs
will be able to make contact, so examine
which ones will be most effective.
Bending open the appropriate tabs
behind the dashboard to secure the
sleeve in place.
1. DIN FRONT-MOUNT (Method A)
Installing the unit
Be sure you test all connections first,
and then follow these steps to install the
unit.
1. Make sure the ignition is turned off,
and then disconnect the cable from the
vehicle battery's negative (-) terminal.
2. Disconnect the wire harness and the
antenna.
3. Press the Open ( ) button to remove
the control panel (For details, refer to
'USING THE DETACHABLE FRONT
PANEL').
4. Lift the top of the outer trim ring then
pull it out to remove it.
5. Use the two supplied release keys to
remove the unit from the mounting
bracket. Insert the left (“L”) and right
(“R”) release keys as far as they will go
(with the notches facing up) into the
appropriate slots at the middle left and
right sides of the unit. Then slide the
sleeve off the back.
Installation Opening
This unit can be installed in any
dashboard having an opening as shown
below:
182 mm
53 mm
10. Reconnect the cable to the vehicle
battery's negative (-) terminal.
Then replace the outer trim ring and
install the unit's front panel.
Notch
Page 04
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber RDD788 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber RDD788 in the language / languages: English as an attachment in your email.

The manual is 0.94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber RDD788

Caliber RDD788 Quick start guide - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info