781509
4
Zoom out
Zoom in
Previous page
1/11
Next page
ENGLISH
7
ENGLISH
6
2. Connect the red wire of control box to positive pole of reversing light,
black wire to the negative, red power wire of camera to the positive
pole of reversing light; (ref: installation diagram).
3. Connect video wire following the general installation diagram.
4. Put the car into reverse gear, the rear camera signal enters control box
and will be output via VOUT after superposing characters.Then there
should be a image with a white dot on the display, indicating parking
sensor entered normal detecting.
Test:A.If the display does not show any image, please check whether
the polarity of the power is correct, the cables are correctly
connected, the voltage is beyond regulated, or the plug on the
display is well connected.
B.If the display is in disorder, please exit and put the car into
reverse gear again. If the problems still could not be solved, the
control box could be deemed defective which needs a entire
replacement.
5. If a person stand right before the sensors within 1m, he/she should be
detected normaly
Test:A.Insert one sensor into control box, if the horn gives continuous
sound and show “0.0”, please check wheter it detected rear
outshoot (such as registration mark, spare wheel, bumper, etc.), the
sensor is fixed too tight or near to some strong interference
sources (such as exhaust pipe, other wires).
B.If it shows distance figure on display without any obstruction
around the sensor, it may detect the ground, please check the
positon and direction of sensor;
C.If the problem still can not be removed, the whole system should
be replaced.
Note:A.This display could be interchangeable, but the connection
between the sensor and control box or the joint end is unique.
B.The display program: it displays “0.0” and gives continuous sound
when the system detects something in the distance range of
0.0~0.2m; the alarm will stop for 1 more second at the distance of
0.5m. Please pay attention to the above note while testing.
NOTE
1.The car must be in power-off during the installation.
2. It’s performance may be affected in following situation: heavy rain, fravel
road, bumpy road, sloping road, and bush, very cold, hot or moist
weather, or the sensor is covered by ice, mud, etc.
3. Switches among ultrasonic and electric wave, DC and AC may effect its
performance.
4.The sensors should be installed appropriate loose or tight.
5. It’s performance may be effected if the sensors are fixed on metallic
bumper.
6.Avoid installing the digital control box in places of great interference,
such as vent-pipe, wiring nearby.
7.Test the system to make sure it works normally before using
8.This system is a reversing aid and the manufacturer will make no
responsibility for any accident after the kit is installed.
Control box
Camera
Horn
Horn
Control box
Camera
Sensor
Sensor
Reverse light
This system excludes display, a display
should be outer connected in addition.
GENERAL INSTALLATION DIAGRAM
PARK 500 manual werkdoc.qxd 28-11-2007 08:47 Pagina 6
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber Park 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber Park 500 in the language / languages: English, Dutch, French as an attachment in your email.

The manual is 1.54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info