169032
4
Zoom out
Zoom in
Previous page
1/34
Next page
E - 3
Installation
INSTALLATION CAUTION
1. Before finally installing the unit, connect the
wiring temporarily and make sure it is all
connected up properly and the unit and
system work properly.
2. Use only the parts included with the unit to
ensure proper installation. The use of un-
authorized parts can cause mal functions.
3. Consult with your nearest dealer if install-
ation requires the drilling of holes or other
modifications of the vehicle.
4. Install the unit where it does not get in the
driver's way and cannot injure the
passenger if there is a sudden stop, like an
emergency stop.
5. If installation angle exceeds 30° from
horizontal, the unit might not give its
optimum performance.
6. Avoid installing the unit where it would be
subject to high temperature, such as from
direct sunlight, or from hot air, from heater,
or where it would be subject to dust dirt or
excessive vibration.
7. Be sure to remove the front panel before
installing the unit.
Fitting the outer sleeve
Fitting the support strap
Remove the transit screws
from the top of the car radio.
Connect the fixing screw to the
rear of the car radio.
Remove the outer sleeve
and place into the
dashboard.
Bend the support strap to
suit the dashboard
aperture and fix to the
underside of the dash
board using the screw
and washer.
Make sure that it is not
angled more than 30°.
Slide the car radio into the
outer sleeve and connect the
spring washer and nut to the
fixingscrew.
DON’T FORGET! Bend the metal tabs on the
outer sleeve outwards and downwards to stop
the sleeve from moving.
30°
Removing the detachable
front panel
Attaching the detachable
front panel
Press the panel release button
on the front panel.
Attach the front panel at the right
hand side first, and then push
the front panel forwards to
lock it securely into place.
DON’T FORGET!
Always turn off the
car radio before
removing the front
panel.
Fixing Screw
Spring Washer
and 5mm Nut
Screw and Washer
Removing the unit
Din Rear-mount
Insert fingers into the
groove in the front of frame
and pull out to remove
the frame.
Insert the levers supplied with
the unit into the grooves at
both sides of the unit as
shown in figure until
they click. Pulling the
levers makes it possible
to remove the unit from
the dashboard.
Fra me
a
b
screw
dashboard
bracket
screw
hook
hook
Installation using the screw holes on the sides of
the unit.Fastening the unit to the factory radio
mounting bracket.
NOTE: The mounting box, outer trim ring and
half-sleeve are not used for this method
installation.
Panel Release
button
2
1
NOTE: If the D.C.P is dirty,
wipe off the dirt with soft,
dry cloth only. And use a
cotton swab soaked in
isopropyl alcohol to clean
the socket on the back of
the D.C.P.
UP SH
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber mcd 786 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber mcd 786 in the language / languages: English as an attachment in your email.

The manual is 2,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber mcd 786

Caliber mcd 786 Quick start guide - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info