168859
5
Zoom out
Zoom in
Previous page
1/8
Next page
EN-4
IN VOL
SEL
2 sec.
SEL
ADJ
SEL
TA VOL
SEL
DSP
1 3
2
4
2
5
2
6
2 2
1. POWER ON/OFF ( )
Press button to turn on the unit. To turn off, press and hold button.
2,3. FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/FADER /
INITIAL VOLUME / CT / TA VOL / DSP
Turning VOL knob (right/left) to adjust VOL/BAS/TRE/BAL/FAD. To select other functions, press the
VOL knob shortly until the desired functions are shown on the display. Figure 1 shows how to control
functions that are selected using the VOL knob.
Fig. 1 Selection of sound control functions
1. VOL 2. SEL 3. BASS 4. TRE 5. BAL 6. FAD
Increase or decrease the volume by turning VOL knob (right/left). These buttons can be used to adjust
the BASS, TREBLE, BALANCE and FADER.
Press and hold VOL to adjust INIT VOL /CT/TA VOL/DSP
INIT VOL: Initial Volume when the unit turns on.
CT:
Digital Clock. To adjust, turn VOL knob to right for hours and turn VOL knob to left for minutes
TA VOL: Trafc Announcement Volume
DSP Modes: CLASSIC, ROCK, POP, FLAT, NONE
4. PRESET STATIONS (1,2,3,4,5,6)
When pressed short, these keys select a preset station directly. When pressed longer than 1 sec.,
current station is stored in preset memory bank
USING THE RDS FUNCTION
What is RDS?
The RDS (Radio Data System) is a digital information system developed by the EBU (European Broad-
cast Union). Piggy-backed on normal FM broadcasts, RDS offers a variety of information services and
automatic retuning functions for RDS-compatible car stereos.
In 1988, RDS became available in the United Kingdom, France, West Germany, Ireland and Sweden.
Test transmissions are being conducted in many other european countries. It is expected that RDS will
be available in most western european countries in the near future.
5. ‘AF/REG’ function (ALTERNATIVE FREQUENCIES)
When pressed short, AF/REG switching mode is selected.
When AF/REG switching mode is selected, the radio checks the signal strength of the AF all the time.
When pressed long, it is activated as regional mode ON/OFF.
– Regional mode ON:
AF switching or PI SEEK is implemented to the station which have all PI codes same as current sta-
tion. REG segment is turned on, in LCD display.
– Regional mode OFF
The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented.
6. ‘TA function (TRAFFIC ANNOUNCEMENT)
When pressed short, it is activated as TA mode on or off
When TA mode is on and trafc announcement is transmitted
– If the volume level was under the threshold point, it will be raised to the threshold point.
– When TP station is received, TP segment is turned on in LCD display.
7. ‘PTY’ function (PROGRAM TYPE)
When pressed momentarily, it activates the TPY ON/OFF function and start to search corresponding
PTY information. And stop if the corresponding PTY information is detected.
By pressing this key longer than 2 sec., you can select PTY mode by turning Volume UP/DOWN knob.
as below.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber mcd 065 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber mcd 065 in the language / languages: English as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Caliber mcd 065

Caliber mcd 065 Quick start guide - English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Spanish - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info