165939
2
Zoom out
Zoom in
Previous page
1/2
Next page
4
B. If the noise is a “clicking” or “popping” that goes
at a rate following engine speed, it is likely to be
coming from the car’s ignition. Make sure that the
car has resistor plug wires and that the breaker
points capacitor is in good condition.
C.If the noise occurs when blinkers, brake-lights,
wipers, etc. are used, make sure that the power
wires for all the audio components run straight
to the battery,not to the car’s fuse box. For safe-
ty reasons you should install a separate fuse box
for all the components of your Car Audio System
as close to the battery as possible. Speaker and
input wires should not run next to wires that go
to lights and other equipment, and you must also
keep them away from the wires of the power
supply to your Audio system.
Specifications:
Caliber CX2
2-way electronic 18dB/Oct crossover
Crossover frequency
High-Pass . . . . . . . . . . . . . . . . 80/100/120/140Hz
Low-Pass . . . . . . . . . . . . . . . . . 50/80/100/120Hz
Low & High output level control
RCA or High Level Input
Subwoofer phase shift switch (0°/180°)
Subwoofer Mono/Stereo switch
Frequency response . . . . . . . . . . 10Hz - 30 KHz
S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . 100dB
Crossover slope . . . . . . . . . . . . . . . 18dB/Octave
T.H.D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.02%
Output gain . . . . . . . . . . . . . . . . . . . . +6dB (1:4)
Dimensions (WxDxH) . . . . . 180 x 110 x 31mm
3
Mounting your CX2 Crossover:
The CX2 crossover can be mounted in any position
using the 4 self-tapping screws provided.
•Vertical mounting provides the best access to the
controls.
•Mount the CX2 crossover so that it is protected
from vibration, possible water leakage and dust.
What to do if there are problems?
Before removing the crossover,look for the problem in
the list below.
1. No output:
A.Make sure that the RCA connectors are plugged
firmly together.
B. Check the amplifier manuals to check for pro-
blems in the amplifiers.
C.Check the power fuse. Both the B+ and the
Remote terminals must have +12V in order for
the CX2 to turn on.You can use a small 12V light
bulb to check for +12V from these terminals to
chassis ground.
D. Make sure that the signal source (radio/casset-
te/CD-deck) is connected and supplying output.
You can find out if the crossover is working by
plugging one end of a set of RCA patch cords
into the crossover inputs, and briefly tapping the
center pin of each plug on the other end with a
finger.This should make a noise in the speakers.
Caution:This may be loud.
2. Only one channel works:
A.Change the position of the input RCA’s.Connect
the radio’s right output to the crossover’s left
input, and the left output to the right input. If the
channel that is out changes speakers, the pro-
blem is in your radio/cassette/CD-deck or the
connecting cable.
3. Noise in the output:
A.If the noise is a “wining sound” that goes up and
down with the engine speed, make sure that all
components including the amplifier are grounded
at the same chassis point, and that this point is
free of paint and rust. Check for ground “loops”,
more than on ground path for any component.
Also try putting L-C noise filters in the power
wires that go to the Radio/Cassette/CD-deck.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Caliber cx 2 crossover at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Caliber cx 2 crossover in the language / languages: English as an attachment in your email.

The manual is 0,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info